Photohigher skyline rsgs

[Photo Higher OM]

Hi Albertocvr,

The only way to ensure you have 1.1.3 on your Skyline is to reload your firmware with the one on our website which is 1.1.3.

 

[Tomvb]

Hi photohigher OM,

Im in contact with Sandor from digitech and i will send the skyline back tomorrow.
thanks for the help.

Greets Tom

 

[MultiHexa]

Here comes the next level: test flight with Skyline

Here and there it is still shaking.
Let's hope it gets even better with the 1.1.4
Maybe I can still improve on what the settings, let's see.

 

[chris hornby]

Pleas let me know what camera/lens and gimbal you are using

 

[MultiHexa]

@chris hornby

Look Page 30 Post 299

 

[nisouck]

With my skyline monted on a AV130, with pan gain to zero, if I rotate my hexa manually, I can see the roll is moving....

Take a look at the screw at the center; version is 1.1.3.

http://www.youtube.com/watch?v=ipLq5DYR1tw

 

[DennyR]

Finally after the change of Tiltservos (Hitech to Savöx), the first test with the skyline.
Here you can see the test:

Roll is OK
Tilt trembles in the movement.

Next step: go flying :nevreness:

If you watch the background you can see quite clearly that any compensation for the actual movement is purely coincidental to the actual disturbance. That is not going to work.

 

[Soaringclauz]

Hello,
i found too that sometimes i loose the horizon. Hope it is something that can be fixed with the next fw. Also i'd like to have the possibility to point the camera upwards. I don't know if 1001copters had success in that but i didn't...whatever i tried i couldn't get it higher than the horizontal.
To Multihexa: IMO the airborne video is good

 

[1001 Copters]

Guys, please be patient

Actually the end course can't be set up .
so you can't define end course other than those already fixed :/

 

[27fred]

Hi MultiHexa,

would you please share your gain settings?
Thx.

 

[1001 Copters]

And please hare it on the google doc used to

thanks

 

[MultiHexa]

Here are my skyline setting for 1.1.3

View attachment 5005

 

[1001 Copters]

Thanks you multihexa

 

[MultiHexa]

@Cédric

again and again:tennis:
You should have a column for the firmware to make in your table.
Just a thought.

 

[1001 Copters]

Thanks a lot for the sugestion, I think evrybody can modify the document but I will do it

 

[27fred]

Thanks very much MultiHexa!

 

[traderc]

I am trying to play with the tilt center servo but no success.. The tilt servo trembles and goes anticlockwise eventually its compensating. ROLL is perfect !!
Did NYBODY EXPERIENCE TESE ISSUES

Finally after the change of Tiltservos (Hitech to Savöx), the first test with the skyline.
Here you can see the test:

Roll is OK
Tilt trembles in the movement.

Next step: go flying :nevreness:

 

[MultiHexa]

You can tilt in the software set to reverse.
Gain Tilt postion shall not be set too high, otherwise begins Tilt to shake itself.
More tips I did not.

We will probably have to wait for the new firmware and hope that everything runs clean.

 

[1001 Copters]

About the gain velocity: it's described in the manual: this is a dampening parameter: the more your push it, the bigger the dampening on camera control will be.
So use it wisely to "remove" vibrations problems.

 

[traderc]

Thank-you.... how can I stop anticlockwise rotation on tilt its very little but its happening
I tried centering the servo frequency
Roll seems perfect and dialed in
Is this the firmware or needs some tweaking on the software and what parameter
Maybe this question is answered already but please one more time..thanks