Search results

Ken, what FPV camera are you using? i am using my GoPro right now but I want to move it over to my MK and my DJI F550. The issue is that for the F450 the camera is inverted and it is a pain to go through the GoPro menu. I would rather have a dedicated FPV camera that is 12v.

When you power the WKM after a short delay, you will get 4 green flashes indicating that Intelligent Orientation Control is available, page 22-24 in the WKM manual.

I agree with Ken, something is not right if you fry servos powered by the PMU/MU.

Naw, you are doing fine. Lots of stuff to learn and remember as you move between different platforms. I just updated my MK and didn't remember that you had to calibrate the gyros to get the gimbal to work. Stupid mistake on my part but a reminder of how many little things we need to remember...

Buzzed, you cannot arm the motors while connected to the Assistant. No motor test like in MKTools. I assume that you have the props off. After you disconnect Assistant from your WKM, repower and arm the motors using CSC. The motors will stop in 3 sec if you do not increase the throttle to...

Thanks for the inspiration. I went out today and bought some ski goggles on sale, end of season you know. I did not cut through the lens but bought some goggles that were meant to be worn over glasses. After I removed the screen unit from the glasses, it just unclips from a mount, I...

I believe that it is. You need to check the specs and make sure that it is capable of "Preset Failsafe". Here is a quote from a Horizon Tech about failsafe. It was about the Naza but the WKM works the same. In the video, the throttle pump was Rx Smart FailSafe not NAZA failsafe. You are...

Buzzed, set the ATTI or center position first by adjusting your sub trim. Then adjust the end points to get Manual and ATTI/GPS. The positions need to be high lighted as well as showing the proper readout on the lower right corner of Assistant.

Just a thought. Make sure that there is nothing that is around opening for the Baro. It could effect the altitude hold. As far as running 10's on the DJI 920kV motors, several do it with success. I have not tried it yet. I have been too busy going from a Naza to a WKM to a WKM with Data...

It looks like the FC is reacting quickly to the slight breeze that was present. What are/were your gains? Are you running 4S with 8" or 3S with 10" props? The hexa is a little more sensitive to wind than the F450. But they are not that far apart.

Ok, it was something stupid that I forgot. You gotta calibrate your gyros before the gimbal will work. It has been a year since I have flown this hexa and it is amazing how much you can forget in such a short time. I have been playing with the DJI's stuff and neglecting my MK. I wanted to...

Thanks, Bart. When all else fails, start from the beginning. I will do a clean install, erasing all the settings, and see if that works this time. I am liking the simplified set up. It makes things, well, a lot simpler and the set up wiki is typically un-German and more user friendly. I...

I don't have any more info that what is posted on the page you posted. My guess is that it will not be an open platform but meant for DJI products only just as the Zenmus connects to the can bus for additional sensor input. I have Data Link and Click and Go. I do not need my transmitter to...

Yes it is pretty cool. 10k range for control and 5k for video link. I think those ranges are for the 900mHz. It should be lower for the 2.4gHz but still impressive. I am interested in how it does as a Tx compared to the Graupner MX series or JR/Spektrum. I know that Sidney has posted his...

Ok, I finished loading v.88 and did the fine tuning to my Dx8 Tx since my JR9503 is in for service, long story. Anyway, I have no gimbal control. I have calibrated the ACC twice and still nothing. There is no power to the servos. I checked my connections to the FC and they are correct. Any...

I don't remember who posted it, sorry, but I do remember that they said the start up speed is dependent on you gain settings. High gains, high start up speed. You don't say what your gains are but it may be something to look at. The posters solution was to set up his gain on a switch, low...

To get your feet wet and have something that will work out of the box, I would start with a DJI F450 Naza ARF. It works well for FPV, is durable and very stable but capable of sport flight in manual mode. There are cheaper options and most of us have tried them. Most are setting in a box or...

I would probably calibrate the esc's first and then do the throttle calibration in Assistant. Make sure that your trims are zeroed, as well as your sub-trims. Your D/R should be at 100%. You can adjust the Expo to your preference.

Welcome whakahere. What would you like to do with your multi rotor? Do you have any RC equipment currently, transmitter, receiver, batteries, charger, etc. Do you have any other RC experience other than the tricopter build? What controller were you trying to use and why weren't you able to...

Boooyv, I just set up my T550 with the WKH GPS. What is your set up? ESC, etc. Are you running with a governor or using the recommended throttle curve. The other question is your mode switch set up correctly moving to highlight ATTI? Pictures really help.