Search results

been waiting a while.. the rumor was end of may.... but they have a habit of releasing a new camera every year and it's traditionaly been end of summer, begining of fall.

my guess is you hooked up non OPTO esc's to the naza, naza has a built in power suply and requires the red wire be pulled from non opto esc so they don't all try powering the flight controller. naza in general is a tough sob,,,, most likely fried the bec in the esc's but there not even needed...

that's one of them mix master turntables.......... yikes, i'd be looking for a better working combo.....

tiger u7, kde 3520 and kde 4014 till the kde u7 killers come out. Unpacking they remind me of opening a new pair of shoes, smells just like it....

It's super easy, you just connect one of the yellow wire inputs from iosd to the cameras signal wire.... i can't remember if the iosd has 12v out to power a camera or not, i use a "buck converter" to power the camera on the monitor we use 3s lipos for all of it.... heat in use isn't a...

I usually put them on a dial and start sweeping through... it'll go from loose to locked in to oscilating then back to the highest point i can get it, then i'll break away the gains that look like they still need tuning and take them off a knob, leave the offenders, start sweeping through gains...

dunno about your exact issue, but when we strip the prop adapter bolts we drill the heads off the bolt, this may work for you, once the heads are off and the adapter is removed, you can grab the remaining bolt with pliers and get them out the rest of the way. most motors are m3 bolts on the prop...

KDE started shipping there new line of XF series esc's this week, my fleets transformation will begin today...... You want to talk about some sexy little esc's, this would be them. they got a nice little heatsink wrapped in the package, these oughta get-r-done I'll be installing 35 amp and 55...

quad/hex/octo? sounds under gained and possibly too low of throttle at hover.... we shoot for 40% min in manual at hover.... less than that and it's like leaving a stoplight in 3rd gear. you will remain more efficient the lower you can keep that hover throttle and keep control.... that's how we...

welcome to the addiction..... get to figuring out orientation and you'll have it made. your full size experience leads you to be more comftorable flying fpv.....

your getting a little interference, try different channels, alot of wireless cable boxes are on these frequencies..... go out in the middle of no where and flip through the channels..... it could be how it is wired up, how solid the solder joints or connections are, what else is where, etc...

this sounds like motor bearings leaving,,,, it's a hot mess..... some ways to physically sort out motors, if any have alot of up and down play, that is most likely broken a bearing..... if you de prop it and fire it up at a idle, mid throttle, rub a nail on the motors and feel for vibration...

most likely one motor is shutting off and most likely there is a bad esc at play, or wire connection/bullet connector. you might have to leave it propped and punch throttle like he said, manual mode, get it to stutter or shutoff... culprit should show. it most likely kept dipping the same one if...

IMO 800 is a tad small to lift a gh3-4 unless your going like zen and a small lens,,,, as soon as you put a real lens and a gimbal that can fly it you want something more like 900-1000mm wide, handles wind better, flys smooth, allows for bigger props and lower kv's as the industry evolves to...

sup

This is THE only company ever granted airworthiness certs on uavs and they have been flying over water in alaska for a year. there just now granted permission to fly over land. They are the largest uav supplier to the pentagon......

it does the self leveling part awesome, the alt hold part is an additional switch you kick on but mine never worked.... it works differently than a dji, not a true atti mode you can just fly,,, gotta turn stuff on and off.... weird controller, but amazingly smooth

i'm not sure,,, might check with sc2000. the case might be the heatsink

the heat sink is part of the pixim seawolf processor. most cams don't have them. what model is yours?

one of the car makers had a futuristic ad recently that showed that