Search results

Those are very high gain settings. I am not sure how they could have changed on their own.

Solar activity effects GPS locks. So yes I was serious. Any changes in your set up requires advanced IMU calibration. I use the DJI escs and have not issues some have with the bullet connectors. I have use SimonK escs on a quad with a cc board. They were ok. That is the extent of my...

You can use ecalc. Google it. It will allow you to check the effectiveness of your set up. I personally fly my F550 with DJI 10x3.8 props on 4S 4000mAh. I like them and also use them on my F450 with H3-2D, iOSD mini and video down link, my favorite A/P platform. When I get the E300...

They actually did the restriction and users revolted and demanded that they get it for the Naza and what is a Phantom but a rebodied Naza. I don't necessarily disagree with you and DJI sometimes may need to just say no and mean it. Some consumers have too much money and not enough common...

Did you check the solar activity for your area? How much time between flights? This is unusual behavior. Also check all your connections. After 6 months solder joints can fail, connectors come loose, you have the picture. I had a F550 with a WKM that banked to the left, rose 60 feet and...

DJI is aware of the issue. It is my understanding that they have a new HDMI board coming out to all GH3 users. I do not know when.

Remove the red wire on the escs.

What gains are you using for Basic and ATTI? I would recommend that you use the gains as specified in the manual. That might help. If you are running default at 100 across the board that could be part of your issues. Go here: http://www.ngdc.noaa.gov/geomag-web/. I am in Las Vegas and I am...

The S800 with WKM can compensate for the unbalanced state of the battery. I am not sure that I saw much drift, you did not just let it settle into a GPS hover and then let it sit. That tells a lot about what is happening. However, have you rotated your GPS for the magnetic declination where...

If you are using the stock DJI escs then they have no built in BEC. No power there. I do understand. When I put my S800 in the air I am looking at over $6k. The pucker factor goes up significantly. I will say if you fly it, you will crash it at some point in time. It happens. I have...

DJ, It has to do with the "smart battery" and the design of the props that are more efficient than the stock DJI 8" props on the P1. I just got a P 1.1.1 that I am installing the upgrade board into and will be controlling it with my Futaba 8FGS. I can swap out the 8" for the 9" Vision props...

No worries on the $5 paypal. You need to have the PMU vsen to X3. I don't know if you have battery warning set up in Assistant. That could be part of your problem. I am not sure why you are reluctant to make the connection? The EXP is the Can Bus port and yes it does supply power to the...

Luke, good to hear that you have replacement props. DJI now has new props for the EVO. They are composite and much tougher than the CF props. They also give 10% greater lift. You may want to look at them also. I would not trash the GPS until you try it. I agree that the damage to the A2...

There is now an other alternative. The Phantom 2 bundled with a H3-2D about 15 min flying times. Less than $900. While you are learning to fly remove the gimbal. The Phantom 2 is very stable.

I am afraid you may have killed it. If it is not initializing you have some serious problems. I don't know where you purchased it from, but I would contact your dealer and see if they can contact DJI and arrange for service of your H3-2D.

They are specified in the manual. You can read it here: http://www.dji.com/download/a2-downloads/

Kloner, I agree. My iOSD is soldered directly to the same pad as the main power lead.

I do feel your pain. I think that your issues are Apple iOS related rather than DJI related. I am still on v6.1.3, I never upgraded. I don't know about the iPad AIR, I am on a Mini. You should have all functions with the exception of sym mode.

I mounted mine on the pad on the LG. I am not sure that that is necessary. I have mounted my A2 on the bottom plate of my S800.

You will have limited channels for gimbal control, 4 only, to connect from the MC to the Zen GCU. Right now the others are not available to be mapped. That may change but no idea when.