Search results

May have found my own answer. After saving the servo configuration, I powered the gimbal off and back on and it's seems to work fine on both axes. Sent from my iPad using Tapatalk HD

I know I've seen this question before somewhere but after getting frustrated searching the forum and Hoverfly help, I'm giving up and asking again. In servo setup, I seem to seem able to configure one axis and save it but not pitch and roll both. I tried enabling, closing and saving one axis...

I like Stratosnapper. I have 2. One mounted on my hex and one to use as a standalone intervalometer. Pretty simple to set up. Sent from my iPad using Tapatalk HD

Pete Take pics showing the battery pack hooked up to the charger or meter showing the low cell or the error message. Get a pic showing the front of the battery as well as the side with the warranty sticker. Make sure that the battery is clearly shown hooked up to the charger with the reading...

I guess I got lucky but HobbyKing treated me okay recently and since I was all set to blast them, I should probably also relate the good treatment. Ordered 3 4S Nanotechs on 3/6. To my surprise, they showed up at my door on 3/9 with standard shipping. Two charged up right away but one...

To enter compass calibration, you rapidly move the mode switch from position 1 to position 3, which is normally manual. I don't know if position 3 must be manual for this to work, haven't tried to check it out. That's the only possible drawback I can think of.

I have the 19 mm Sigma in E-mount and I like it a lot for the price.

I've got a Sigma 19 prime that I like a lot.

This was cool but it would have been even cooler if Keanu Reeves had followed him out the door without a chute.

Just so I'm clear here, if your screws are the stainless alloy that is non-magnetic, are they still a problem or can they be used safely without causing mag interference?

Are all stainless alloys magnetic (I think thats the term I'm looking for)? I'm building a Rusty's frame and the fasteners with the frame weren't attracted to a moderately strong magnet I tried to pick them up with.

And hope the neighbors don't call the cops and report a drunk guy whirling around in the front yard.

With the talk of building a waterproof multi, thought some might find this interesting. http://www.waterbeader.com/

For portrait photography, a slightly longer than normal focal length is generally considered to give the better perspective for faces so stick to the upper end of your zoom lens. Extremely backlit scenes are tough. The simplest way to combat it is with a fill flash. There are a number of...

Photronics just posted an interesting video in Hoverfly forum demonstrating the degree of mag interference which could affect magnetometers in GPS units. That led me to wonder; I can mount the GPS unit as far as possible from suspected mag sources but the cable is very long and I always seem to...

I need some help getting my NEX5N to fit on my AG550v1.5 with an HDMI cable. Enclosed is a pic of the tray. With the camera installed, there is less than 1/2 in clearance on the side. I have tried a couple of cables including an ultra-thin and a right angle and they don't come close to...

Where yours is 5.5 cm deep, mine is only 2.54. Total width is 12.7 cm and width between the bolts is 12 cm.

Here's my tray. Wonder if it looks like yours. I have v1.5 and that may be one of the differences but I still don't see how to fit a HDMI cable in there. As near as I can tell, I placed my order on July 31 and they stopped taking orders on Aug 1 in anticipation of the revamped version. Should...

I don't have two slots in my tray and i don't see anyway to adjust the tray itself. I'll send a pic when I get back home. I should have the latest version, I purchased mine apparently right before they took it off the site in anticipation of the newer model. I wasn't too happy about that. If...

Gary, I apologize for using this method to reach you but I have posted a couple of queries on your site and received no response. I have a recently purchased AG550 for Sony NEX. When I mount the camera, I have less than 1/2 in clearance on the side. I have purchased two different HDMI...