Search results

Did you make the H loom to power the skyline ?

I'm not Photohigher ^^ I'm just a reseller that in involved in this new product :) I strongly believe that this kind of stabilization system can be one of the best available. It just need some tweaking. I really understand users thats are very disapointed by the skyline because it has been sold...

Hi Aviator, I was answering the particular question of Titusx where he ask :"perhaps it's my gimbal ?" No concerning hat you say you are right. I have already proposed to my customer that want to return the product to refund them. Some of them trust the capacity of the product and want to wait...

Hi Titusx, you can read it like this but what I see is: "we can not garantee how well it will work". It has been annouced very early that that the Skyline will be designed for AV130/AV200. before it was available for purchase if I'm not wrong. edit: I posted it on this board: this one ...

Hi Aviator, as already said, the Skyline has been designed for AV130 and Av200. There is no support for other gimbals. The autune function calibrate the gimbal but reaching the limits of the AV130/AV200. if your gimbals have lower angles limits, yes you will have a problem.

Hi Dominic, the issue about the roll being mad when you cut the power on skyline is only dur to a bad calibration at startup. If you follow the manual, remove the belt and roll gear, set up the servo like indicated you have no roll and tilt issue when you cut the power off. The 550D fits in the...

Where did you buy your AV200 ? this is your reseller job to change the defective 72 teeth wheel normaly. We have received some spare to replace the defective ones. By the way, It's hard to imgine that you put your 40$ potentiometer in the trash (the roll one) because it's a pretty good one that...

Hi, the skyline is designed for Photohigher gimbals. their is no support for other gimbals or servo other than those used on AV100/130/200. The skyline is working by sending an idle signal to the servo an it controls it by the potentiometer input. The Hitec servo are not comptabile with this...

Hi, it's recommended in fact :) Actualy the skyline doesn't handle the roll control nor the pan control. to have the pan control, you must plug your pan servo into the receiver. Before powering, remove the belt o your pan sero and then power up your system. once done, trim your pan servo in...

Well the zenmuse don't use servos but other kind of motors so the problem is different.

Hi Oti, nice to here you :) I'm not a profesionnal in images but to demonstrate the property of a stabilization product it should be a good idea to use a test protocol. what does customers want to see ? - is the horizon is well conserved on small movments, bigger movments - is there some...

Your cable is probbaly faulty. Contact your reseller and ask him another one ;)

Hi, the stuff to test 5.8Ghz antenna cost nearly 10k€, not 200 :) You can build your own system but you don't have ANY insurance on the measure given. That's why I have payed a company. Terry has build his own SWFR meter but he didn't have any reference to calibrated measure. By doing these...

Sorry, this is the MK2, not the Rmk2 :) http://www.helimag.com/articles-review/25405-la-pinwheel-par-terrybuild.html The best couple for long range FPV should be an helix + pinwheel accorded together yes :) By the way, in 5.8 Ghz I strongly recommand NOT to use any convertor (N type to SMA...

hi, is there any circular polarized patch antenna ? I only knew about patch antenna with vertical/horizontal polarization. if you mix a circular polarized antenna with a linear polarized antenna, you loose 3db of gain. on a patch antenna it's ok because you generaly have 9 or 12dbs of gain but...

Hi, pinwheel and cloverlead are a bit different ( in angle of the lobes) The SMA and RP-SMA difference is the connector not the polarization. With this quality of antenna you really don't need to mix cloverleaf/skew planar anymore :) To protect my pinwheel I place them inside a ping...

Hi, I have made a test of the Terry Build antenna to compare between a rubber duck antenna 12db and a Terry build pinwheel. As you will see in the video, The pinwheel enhance the reception in perturbed environment. A good video tells more than a long speech ;)

Hi there, First of all, be carefull when you make these changes, if you misunderstand something you can fry the Skyline. The purpose of this cable is to cut the power from the skyline to servo. the wiring proposed can be done with standard servo connectors. I will do a video this week end to...

Hi guys, I'm turning back from a long week end without testing (but with wonderfull food tested :p). About the zenmuse and the comparison of the product: it's clear that the zenmuse is a step above all other available gimbals for GH2 and NEX5 camera. The technology involved is completly...

If you don't find anybody in USA to do it , I can but the shipping will be long and costy :/