Search results

After A few test flights and some gain tweaking here's where I'm at with mine... Tilt is locked in, roll still needs work. This flight was done with the roll gains raised to see what effect it would have, does a similar twitch at lower settings. I'm wondering if some of it is the AV130 being...

If you already have external pots connected to the servos on the mount the servo mod has already been done, then all you need to do is disconnect them and use the "dummy pots" which is a servo connector with a pair of resistors as shown in the installation guide. Ken

I bought one of the KK2.0 and put it on my F330 frame with a set of 1340kv motors. Thing is crazy fast in every direction and it's really stable compared to the other versions of the KK that I have, the autoleveling sort of works, nothing at all like an MK or DJI, more like the Quadrino board I...

Boat, seawater, ummm, no... I turned down an offer to do aerials for Shark Week off Cape Cod mainly because the conditions were the same, not risking equipment loss for a few $$$. Crashing over land is one thing, dunking all of it in the ocean with zero hope of recovery is another. Ken

I do not need another TBS Disco, I do not need another TBS Disco, I do not... ;) Ken

Odd, I'm landing at 10 minutes and the packs are at roughly 70% discharge at that point, same frame, motors, props, batteries, plus the vTX, GPS, and OSD. What flight controller are you using? If it's a Naza, are you flying in manual, atti, or GPS mode? The other thing I found is the Nano's...

With a big leap of faith I went ahead and setup the RSGS on the Cinestar/AV130 today. Had to completely disassemble the harness and rebuild it according to the new schematic, getting rid of a bunch of wires and connectors in the process. Since I'm only using tilt and roll I've got it down to 4...

Hmmmm... I have a Cinestar 6 with P/H AV130 and live about 30 minutes drive from the Cape... Have to see how things go this weekend with the Skyline RSGS I just installed, may still not be quite ready for primetime. Ken

Maybe not quite on the scale of the H/F event, but we're (NEHC - http://nehelicrew.com/phenomenon) having our big event of the year this weekend and for the first time we're having multirotors be a part of it along with the usual 3D and Scale helis. Wasn't hard to get it on the schedule, the...

My brain reached a compromise, I'll take the RSGS off the AV130 on the Cinestar and put it on the old AV130 backup gimbal on the Droidworx AD6, if it can make that old warhorse stabilize well then it's a winner! ;) Ken

I just upgraded some of my 5.8 gear and I'm getting results almost as good as what I can do with my high powered 1.2 gear. The key to the performance was two things, the RX and the antennas. I upgraded from the Immersion Uno to an Immersion diversity and I'm using am SPW on one side and a 10db...

I have an RSGS mounted on my AV130 but not connected to anything at the moment. I bought this one from the initial production batch, got it all setup and ready to go, and on the first test flight the YS-X6 decided to flip the CS6 on take off breaking a couple props and tweaking the roll cradle...

Must be something unique to a particular batch or maybe the newer Naza, I have three of them flying now and not one of them has this problem. The newest one I have is at least three months old, probably more, time flys when you're flying FPV... ;) Ken

If you want to disarm just do the motor start sequence while they're running, it will stop the motors and put it in an unarmed state where they can't be restarted without doing the CSC sequence again, if you have to move the control sticks to get the motors to start then the board IS disarmed...

1) Is the public allowed to attend? Yes, the public is invited. I can bring my wife and daughter? Yes you can, we don't charge admission either! Parking? Onsite, plenty of room and also free. Directions? Location: The entrance to the field is: 41.991608,-71.243052, which is located across the...

I have both basic and atti gains TX adjustable, I can set it to whatever works for the prevailing conditions as I'm flying. I have the basic gains set for a range of 80 to 140 and the atti for 50 to 120, the yaw is fixed at 200 or 250, I forget which, and the altitude to 200. With the yaw and...

Check the plug where the wires from the servo connect with the wires that go to the roll potentiometer, you will likely find it loose or about to completely disconnect. The other issue could simply be the roll servo centering is way off to one side, the way to fix that is loosen the rollers so...

There's a general aviation field in Mansfield maybe 4 or 5 miles from the NEHC field so you could easily fly to the event though I'm not sure about the availability of ground transport at the airfield. If you decide to head up I'll be at the Phenomenon in Mansfield on Friday the 14th and...

I'll be at the NEHC Phenomenon in Mansfield Friday the 14th and Saturday the 15th, unfortunately I won't be able to be there on Sunday as well. I'm scheduled to do a multirotor seminar at 3:00 PM on Friday and 11:00 AM on Saturday, the remainder of the time I'll hanging out at a 10 x 10 popup in...

I've used gimbals from both companies, I currently own a pair of Photohigher AV130 and nothing from P-1, that pretty much sums it up. Ken