Search results

Have these DJI LK900 Mhz transceivers been successfully installed on Notebook PCs by anyone else here in North America? I recently purchased the DJI Ground Station c/w LK900 Mhz from a Hobby shop in Mesa, Arizona for my WooKong M GPS (supplied thru Empire RC). Immediately upon connecting the...

http://diydrones.com/profiles/blogs/rc-lanc-controller-for-sony-canon-panasonic-video-cameras

http://www.youtube.com/watch?v=LPGb4WK_fkk

Very professional video work and clear voice annunciation. Just one question... At 30 seconds into this video "Programming the Wookong M CH 2 Software Overview", the IMU coordinate configuration shows a "-6" for the z axis. How is this determined and/or why is it not zero? I get the impression...

Another item to consider.......There is also one serial number required for each NAZA system and monitored and controlled by NAZA assistant. If the serial numbers are lost or mixed up there may be issues.

Should it still be of any use to you..... I have found the Naza setup file ???.naza and can send it to you by private email. Note: Reveal your email address by private message only. It is loaded by means of the import function at the top of Naza assistant software program. Note: I cannot accept...

But did you successfully install your USB driver first? This would preclude all other efforts to upgrade firmware or even communicate with the Naza. Is the blue light in assistant software flashing on/off?

Avoid the Youtube videos for now as they can mislead if you haven't followed the DJI manual as closely as possible first. Connect USB cable between PC and Naza controller before applying power to MR. Install correct driver Update Naza firmware Start Naza Assistant configuration of NAZA...

You seem to be saying you have both the Naza and the WKM, i.e., WooKong M... They may look very similar but there are major differences in electronic components, firmware and the assistant software. Even the inside of the GPS/compasses are different. Best not to mismatch any of the firmware...

Will drop by my house later to grab the Naza config file. In the meantime here is one of two Youtube videos posted by Jon DesJardins that helps with Naza setup but with Futaba. http://www.youtube.com/watch?v=SmDehc5PEUQ

Seems to me that there are only four terminals on a USB connector so there is not much involved in wiring your own with servo connectors or alternate RCA connectors, standard pinouts at both ends. Those RCA-USB cable sets are a standard product provided with a wide variety of cameras over the...

Maybe I should send you a copy of my Naza config file downloaded from the EEPROM...... but you still will have to match the Naza config at your transmitter end and my config is for a Futaba not Spectrum.

Calgary continues to grow both in population and prosperity by leaps and bounds and is now at 1.3 million approx. Winter is not so nice though as daylight is so short in the winter with too much cold and snow etc. "no batteries included/some building required" but there is always Internet...

Yes... some of the videos are tend to mislead as does the documentation. And jumping back and forth between a NAZA and a WKM is even more confusing.

You are getting very close now. I don't have the Spectrum RC system but am familiar with your situation as it applies to the Futaba T8FG Super. You simply need to get the joystick alignments as close as possible to the horizontal and vertical midpoints for each axis when calibrating your Tx to...

The GoPro 4 Black edition has only two ports which are the USB port and the HDMI port. I get the impression the previous GoPro's had a phono jack connection and there is not yet a cable available to connect the GoPro 4 to an FPV system. I suspect, if it is even possible, this would have to be...

Might be that your gimbal system mechanically jammed. If it did the current draw on the two servos might be enough to sink the power supply voltage into the brownout region for your NAZA..... and all bets are off when your flight controller enters the Twilight Zone!

I have the Hyperion 1420i-Net3 charger and want to simultaneously charge two 3300 mAH 3S battery packs which I use in parallel for flying. I assume these both can be charged simultaneouly but it seems I have to charge them in series as per the following...

Disconnect a motor. Connect all 3 leads together and try to spin the motor. If the spin is further impeded when the 3 leads are connected together, your motor windings should be fine (magnetic drag). Also you can connect a multimeter and check continuity to the case. If not continuity, there is...

See page 9 of the WKM manual..... X1 is reserved for the PMU and X2 is reserved for the Futaba s.bus connection. Remove servo cable from X2!!