Search results

I read several months ago that a good test for any carbon fiber prop before installing is to flex it and listen for pops or a cracking sound. This would indicate the the carbon fiber was weak and should not be used. I ordered several sets from RCTimer and started using them on two MC after...

I've been their motors on a RCT800 build and so far... no issues. now their carbon fiber props are another thing. I've had 5 fail so far.

I've wasted too much time fiddling with batteries and it's not worth saving a buck or two when it comes to flying expensive equipment with cameras attached. If you want to talk to the manufacture directly and get their personal recommendation as to what you ideally need call MaxAmps in Spokane...

I have been chasing a very similar issue. The gain settings were the cause. My current setting are: 180.180.160.170 atti 160.160 It was the atti numbers that really made the difference. It may not hold a extreme specific position while in atti with the wind but it sure does respond a lot...

DJI offers a great range of products and I use them on my two multirotor aircraft. What they have failed to do is control the re-seller channel, there are hundreds of web sites that offer DJI products... the majority of them have no knowledge of these products. I spent $500.00+ this weekend on...

Maverick, I currently have a LED trigger for the NEX shutter release. Do you think that the one you have is unique in the ability to control the shutter and start and stop the video? Did you do any adjustments to your Tx to allow this ability? -Bob

I currently have my Futaba Tx configured to trigger the shutter on the Sony NEX camera using a 2 position switch. Starting a video capture requires manual operation before takeoff. Using a 3 position switch on my Tx can it be configured so that in one position it will start and stop a video...

During the last several flights on a RCT800 using the new DJI NAZA M v.2 I've noticed a unique twitch in the flight. It's like the chill twitch we experience.. short, sudden, and very noticeable. I have replaced the Tx and RX, disassembled and checked all the connections, still happens. Will...

Make sure the controllers are not reversed. The stick movements for the throttle and elevator are the most challenging. When moving these controls forward the software should show the arrow traveling to the right. Once that is confirmed, be sure and do an Advanced IMU Calibration and a Command...

Your answer is dependent on the props, battery and total weight of your multicopter. But with regards to the RCTimer ESC offering, I'm using their 40 amp ESC's with great results. http://www.rctimer.com/product_850.html

It is my understanding that a brushless gimbal needs it's own controller. The NAZA is suited for standard driven servos, not brushless motors.

A while back Ben Rowland with Yonder Blue Films did a comparison between the GH2 vs. GH3 https://vimeo.com/59001892 https://vimeo.com/58942114

My 2 cents worth. Have both versions. 1.5 years of flights, no issues. Would use a NAZA again and recommend them to others

My experience on props for my F550 has been extended to the RCTimer offerings. I have a complete set of their carbon fiber... 9x5 http://www.rctimer.com/product_864.html 9x4.7 http://www.rctimer.com/product_793.html 10.4.5 http://www.rctimer.com/product_946.html 10.3.8...

I'm having a similar problem except that after the twitch ( mine will twitch twice very fast) accrues the flight controls on the right side of the transmitter rotate 90 degrees. Makes it a difficult to land. I'm going to swap the Tx and Rx with another unit and test.

Very excited about having these new features, thank you! On a personal note having the ability to use an android device would be very much appreciated.

FYI, the dealer I'm referring to is listed as an authorized DJI dealer on DJI's site. They have said several times that they are the largest DJI dealer in the US (selling 20+ fully built systems a week...) and that 80% of his business comes from professional customers. Hobby Shop is part of...

Inquiring minds what to know. I'm having a struggle with my local dealer and would like a second opinion form those that are in this as a commercial application. I have been very local to the dealer in Atlanta and have purchased a large majority of products from them. Mail order sites can...

I've installed the Sky Rover system, gimbal and landing gear. After upgrading to the Hitec's 7235 digital servos I've found that it works fairly well. There is no doubt that the new brushless gimbals will offer more stability but they require their own controller. http://skyrover.us/ Best...

$30.00 for two graupner props is a bit on the high side; but since they are not in production anymore this may be reasonable. The RCTimer CF 9x5 props are $32.93 for four (4) pairs. I've been using their CF 10x3.8 props with terrific results. With over $1,500.00 in camera gear along hanging...