Search results

I know the manual recommends 2-6s but what is the max? is it 6s can can these flight controllers take 8s? If not, is there a way to get around this? Thanks

I have done a bit of searching but don't seem to find much. Do these trainer cords exist? Wanting to link a DX9 with a 14SG Thanks

I'm wanting to use the new KDE 5215 motors with the 55A ESC's. The ESC's have 3.5mm bullets but the motors come with 4mm. As I have to cut the motor wires down anyway, I was thinking I would replace the 4mm motor bullets with 3.5mm. I'm just not sure of the Amp rating on the 3.5mm bullets...

Can someone please help me with a few questions I haven't been able to find answers too. I'm looking into the 2.4 datalink and what I can do with the ground station. I'm pretty sure you can set the heading between waypoints and also at a waypoint?? but can you yaw the craft manually between...

Just wondering if the HoverflyGimbal controller will work with S-Bus? Thanks

What is the general consensus on the best plug to use on the bigger skyjib type crafts running 6s batteries?? Thanks

I was flying my MK today just above the ground when a shower of rain came over, the first 30 sec was ok but then it just flipped forward and went down. The only obvious damage was a broken prop and boom but thought I'd strip it down to check. I'm not sure if it was the rain that caused this or...

My X8 has been flying great but have noticed in the last couple of flights that it has been doing some intermittent motors pulsing (with AH OFF) that last about a second or 2 each time. During a 5min flight it might do it about 3 or 4 times. I'm using Pulso 2814/22 motors, 30amp Turnigy Plush...

I'm using the R6203SB with the 14MZ and wanting to add a 360 pan to my AV200. What is the easiest way to connect up the pan servo. There are channels 1, 2 and 3 plus the S-Bus port but I'm unsure how to connect extra servo's up to the S-Bus receiver. Or the MK FC. Any help would be appreciated...

I'm using a droidworx crash cage which has a carbon top so need to look at other options for the GPS. I see some mount their GPS on the boom. Do you also need to mount the Navi-Ctrl on the boom with the GPS or can you have the FC and Navi in the center and just mount the GPS itself on the boom...

I'm just changing over to S-Bus so I can use the MK failsafe. I'm using a 14MZ and have used up all the 12 channels that MK tools will show. I'm wanting to set up a failsafe channel so I can test the failsafe with a switch rather than turning off the TX - it takes too long to turn back ON if...

Could someone please tell me outside diameter of the AD series booms? The wall thickness would be great also if possible. I'm wanting to know if the booms on the AD and VM series are the same. Thanks

I have 2814/22 motors with 30amp ESC's and wanting to lift a 550D and AV200 with MK electronics, 4s batteries. Will a VMX4 do the job or would you suggest going up to the XMX4? Thanks

Can someone please tell me if 600Hz will be any better than 400Hz when used with the DJI WKM? I've just seen that Multicopter have their own branded ESC's with SimionK firmware which use a atmega8 chipset and 600Hz. Then there are the T-Motor ESC's that use a silab chipset and are 400Hz. Does...

Does anyone know how the different kv motors handle the wind. I'm looking to use 400kv motors with 15x5 props on an X8 but am wondering how this setup would compare to using 670kv motors with 13x6.5 props when in windy conditions. On the face of it, it seems the higher kv motors (670) would be...

I'm looking to build a Droidworx Skyjib lite X4 and trying to decide on the best motors to use. Most seem to be using the Axi motors 2820/18 that have a KV rating of 670. I'm wondering if anyone has used the T-Motors and how good are they compared to the Axi motors? Thanks

I'm wanting to get the datalink so I can use the waypoint feature but am also wanting telemetry showing packs volts, distance to home etc. Does the datalink show this info or do I also need to look into the iOSD? Thanks Craig

I'm looking at switching to DJI after using MK for the last couple of years. The machine I'm looking to build is a X8 but am not sure on the ESC's that I should use. I have been looking at the Turnigy Plush 40amp ESC but have also seen some using the 40amp Hobbywing. Is there a recommended...

I've been having all sorts of issues after about a year of everything going very well. So I thought I'd update the firmware in the following order: Navi-Ctrl - 28o MK3Mag - 23a Flightctrl - 88n The navi updates no worries, but when I get to the MK3Mag it only transmits about 50-60% of data...

I had been flying my X8 for about a year without any issues,and made no changes, then for some reason it started a toilet bowling circle after about 3min flight and did this for about 5 or 6 flights with only about 1 good flight in between. I checked the gps battery and it at about 2.85v. A...