Search results

we use two vtx and two groundstations. it also takes 2 complete radio systems so no breaking out anything. one controls the craft, other controls the gimbal

post a picture the bigger power wires between esc and motor..... there is usually a bullet connector on that wire near the esc's.

swap any 2 of the 3 motor leads..... the wires that plug into the esc, the bigger usually black wires.

Sleepy, is that you? haha the movi guy shoulda ridden one of them things.....

I haven't passed the S part yet.... but am starting to settle in. It's some crazy pressure were all under trying to do this to go to work..... Glad your hangin in there.

Got my first three supervised solos done so tomorrow is my first unsupervised. Next after that goes back dual to intro 180 turns, short field and soft field intro then night. I wound up sicker than a dog with some stomach virus after my second solo where i was having communication problems. I...

The gui doesn't let you reverse any input so on each brand radio the sticks gotta be reversed in the needed direction... page 10 http://cdn.shopify.com/s/files/1/0239/9015/files/XAircraft_SuperX_Manual_EN_v1.9.pdf?850

it's a lot of weight in motors for the frame size/props you can fit. if you could get 17" props on it times 8, your gonna need to down size the batteries, down size the motors to hit a sweet spot. 4014 would be somewhat big but they like 18" props best.... 3520 would get you in that same...

it doesn't come off very easy so we use welders glue. it's bullet proof and totally removable. it's a contact cement that never totally hardens, you stretch it and it falls off. we only use it n connectors that don't have a lock and are generally loose like some servo connectors into fc's. if...

I'm 8fgs through ezuhf and the other is just 8fgs with 6208 and it just works..... Is it possible the guy with the problem doesn't the reverse done right per the instructions? if he does, it;s an end point and stick calibration needed, not just an end point and try....

you can't get them to enter a endpoint calibration..... there locked up with a permanent end point set in the firmware.... like dji with what your explaining how the other esc wouldn't arm either is a consistent problem with your radio to superX issue, not an esc problem. it is your endpoints...

i have zero experience but people i see doing three d printing have there metal parts machined,,,, the tolerance isn't very good, at least like what a typical bearing shaft/support would need.

futaba are great, i thought the guy with a problem was spektrum? cause that's the ones along with tyranis and hitec that have a history in this thread to have endpoint issues.

to go fly this thing on a maiden it's fine to use whatever, can even go an inch or two smaller but to film and fly, your gonna want something cf and preferably t-motor. any prop your gonna get will take balancing, the cheaper the prop the more likely it's too far out of spec to balance safely...

the SuperX is my favorite..... loves wind, feels slower to correct like hoverfly used to but has gps functions that work. work really well for us, heavier the load the better it works.... heres some footage from them

the wires are bent backwards, unbending just breaks em. if nothing else get some wire and make new lobes. i'd just cut that end off and make a normal ib crazy lobe set. theres a signal and ground lead up in there and the solder can't cross poles or it'll not only work like crap but blow up the...

just in case it wasn't tried, you want to drop your throttle end points to like -125 +125It's been consistently people not using futaba so you gotta bob and weave through setting it up. after extending the end points on the radio, redo the superX stick calibration, then try booting it up

It's the grey area that shutdown Chuck and his display at the show. It really is messed up

even making the motion to do something that can be paid for isn't seen as hobby use is it?

nope, you screwed the pooch. you have the equivilent to a square peg and a round hole instead of altering what you have there, to take on antenna altering is easier to take on antenna making. Follow the threads at f p v l a b s .com from ibcrazy to make one from scratch or order the right one.