Search results

With the 75amp ESCs I am only getting 3.9 minutes of flight time... Also, motors overheating. It is a tough balance...

I have been on their FB page for a while and looking at users work and what I see looks as good as what I have seen on friend's MOVI rigs in the real world. I think both these gimbals are basically as good as setup and the operator as long as you got a good one off the assembly line...

It is finally time to build a true heavy lifter capable of flying a Red / Canon C300 / BlackMagic 4K etc. We have been doing lots of work with the S1000 / 5D MKIII and the new S900 / BMPCC packages but more and more our clients are asking us to fly bigger cameras, a greater variety of lenses...

I am on 1.18 shooting NTSC.

OK, got work around here. I boot up in 29.97 and get signal then switch to 23.98 to shoot. Boom!

DJI said to send it back but that really is not a good option as I have a job with that camera on Sunday and I need this to work. Obviously video downlink is critical...

I did as a matter of fact... Is there any way to go back?

Got a problem with my Z15-BMPCC gimbal. Everything was working great but now all I get on my video monitors is the data overlay from the iOSD and a white screen. The data overlay is telling me that my video TX/RX is fine so the problem has to be in the Z15, the wiring or the iOSD. I have...

I have been trying to set up single operator for my S1000 / Z15 5D rig. I have dual 14SG TX's and R7008SB RX's and thought it would be easy to set the gimbal RX to MODE 4 (ch9-14) to do so. I would then remap the controls on the TX to accommodate this change. THis way I can have full control...

For some reason when I changed upgraded to my new Futaba R7008SB RX/14SG TX package the other day from my old R6208 RX / 8FG TX for gimbal and camera control I developed a problem. Camera settings have not changed but now while recording the 5D stops and snaps a still every minute or so. It...

Yes, but I do not have this rig set up to fly in manual.

Ok, just built up an S900 with an A2 I had around and had a weird test flight. In GPS mode red blinked 3 times, 2 times, once then all LEDs stopped altogether. Yes, I did imu and compass Cali. Switched to ATTI and LEDs normal. Tried very low flight in ATTI and all was well. Any ideas??? I...

Thanks for the advice. Droidworx (Aeronavics) recommend the Gremsy H14 Gimbal . Has anyone had any experience with this? It looks pretty good...

Ok, time to open another can 'o worms here. I have been flying for a couple of years and getting work with my S1000 / 5D combo. Just took poscession of an S900 / BMCC setup for folks who want that too. Trouble is directors keep asking if we can fly the Red and I think there is a market there...

I just upgraded to the A2 2.3 firmware and I am a bit scared. I was at 2.1 so it had been a while. When I first booted up I had lots of errors (controller, sticks calibration, compass etc). This morning it is just compass which worries me a little. Especially now that I have a gig in 2 days...

I have tried everything in the manual and I just can't get this thing to start in mode B. This RX runs my camera and gimbal and I want to create a solo setting on the TX so I need to get access to channels 9-16. Help!

I guess what I need to know is how to map channels to specific receivers or, if that is not possible how do I change the mapping of what the channels do in the TX.

I am trying to set up my S1000 / Z15-5D rig with two flying modes. 1) Dual operator - dual RX,TX etc and 2) Solo operator - single TX, dual RX. THe dual operator is working perfectly as I have the Futaba T14SG and two R7008SB RXs linked and working via Sbus in 14channel single mode on the two...

What about lens stabilization?? Great advice. Thank you!

So I finally have all the pieces back together and have my Canon 5DMKIII back up in the air on the S1000 with the Z15-5D gimbal and the recommended 24mm lens. Now for camera video settings and work flow... I've been shooting stills with Canon DSLRs forever but video is relatively new to me. I...