Search results

So the best route would be 4s. Can 1038 be used or would I need to go 9x5?

Moving from the DJI F450 frame, I purchased the HJ MWC X-Mode Alien Quad frame and moved all the components. I am running iPower 2217-950kv motors with 1038 DJI props, 30amp DJI Opto escs, Naza-m V1 (original), DJI look-alike legs, and tarot T-2D gimbal with gopro 3 attached. The batteries are...

That's the site...

So I posted over at fpvlab but never received a response. Anyway, I managed to fix the sensor. Immersionrc site has a beta version of the immersionrc tools version 1.22. This version has a sensor calibration wizard for end user and retailer. All is working now. My only other issue after testing...

I have this thing connected to see if there are any changes to what the sensor is reporting in terms of the voltage. So far the voltage reading is dropping past the battery voltage. If I connect another battery, the voltage reading goes back to 60v.

Going to post pics of the sensor later this evening. I purchased from futurehobbies. This sensor is also the 100a version.

I posted a little while ago. Hopefully it's something I can fix myself.

There is no rssi cable. Everything connected is ImmerconRC compatible. Page 4 of the manual show exactly what I have connected. The plugs used are the ones you can only plug one way. The lipo is connected to the battery input of the sensor and the sensor feed power to the OSD. The esc connector...

I received today the EZosd and installed per the diagram in the manual. However, everything is working as it should but the sensor is reading a higher voltage of about 58volts when I have a 3s battery connected. Not sure what to do. Is the sensor defective or is there a way to reset? With a 2s...

I have a question. Is it possible to use a cloverleaf antenna on both receiver and transmitter and are there any benefits in doing so? What about doing the same using skew-planar antenna? Just curious.....

I will give it a shot flying it forward some few hundred feet and see how it goes this coming weekend. I'm just confused because I have seen many other fpv videos where the quad is close to the receiver with no issue. Perhaps they are using a patch antenna? Perhaps I guess. Really do appreciate...

Nope, this is just for testing. Actually the quad is not above the receiver but maybe about 10-20 feet out from my position. I also yawed the quad just to see what would happen. I'm gonna give a a fly run with the antenna on the right arm and see how things go.

Ok, I moved the transmitter over to the right front arm and also installed a 90 degree elbow to the antenna. Still have same issue. Quad is high above tree line and LOS. If I go higher the staic gets worse. I also tried putting transmitter in back under the quad belly. I was able to shoot a...

Thanks for the basics..... You say the VU produces alot of rf garbage. However, having the antenna in horizontal position gives me the best video without loss. I did initially have the fpv antenna on the left front arm with rc receiver just behind it on the plate and that did not work. I'm going...

I'm not sure why video range is bad when I go about 25ft above the tree line and start to lose video signal. Static first then loss. I have setup the ImmersionRC 600mw transmitter - 5.8ghz on a DJI F450 frame. On the frame I have the gopro2 in front and DJI GPS on the back. For receiver, I have...

I'm running my Naza using the S-Bus and same receiver. Radio is the Futaba T8FG Super. Take a look: http://www.rcgroups.com/forums/showthread.php?t=1670521&page=4 post #60

The ESC's I'm using are Hobbywing Flyfun 30 amp. Never heard of iPeak esc.

I'm using iPower 2217-950 (950kv) motors on my F450 with APC 1047 props. No issues so far.

I'm running 3s 2200 @ 30c

I'm running Hobbywing Flyfun 30A esc with turnigy D2830/11 1100kv motors and have no problems. Timing is medium.