Search results

  1. T

    First build problems NAZA M V2 F450

    My guess is probably yes. A good test is to move the motor and see if the problem follows the motor or stays with the esc.
  2. T

    DJI S1000 Owners Thread - Mini Build Log

    I did the files are sequential.
  3. T

    Onwards and Upwards !

    I built 6 of them for NAB in Las Vegas. It was a lot of fun and I agree that the quality of this copter is superb.
  4. T

    DJI S1000 Owners Thread - Mini Build Log

    You can open the file in the iOSD Assistant then go to Data View. It then gives you the data logger as an accessible remote storage drive.
  5. T

    How would the DJI Ronin mount to a Multi Rotor?

    There is an adaptor for the S1000. Unfortunately the proper parts did not arrive from China to the show. I don't think that an Epic Red was part of the plan. D5 with various lenses would work in my opinion.
  6. T

    H3-2D issue

    You need to calibrate the X1 channel, i.e., tilt in both the RC Assistant and then in the Phantom Assistant. That will fix your problem.
  7. T

    Failsafe (yet again)

    If you are using a switch to move to failsafe, I am assuming that your are flying and the throttle is above 10%. You will be fine as long as you don't drop the throttle to less than 10% and then hit the switch.
  8. T

    naza lite sbus and 10j

    Have you set the receiver type to D-Bus?
  9. T

    Batteries -- A big one or two in parallel?

    Several guys that I know fly with 2x10,000 or 1x16,000. It is a personal choice.
  10. T

    H3-2D issue

    Calibrate the X1 channel in RC Assistant then again in Assistant. That should fix the issue.
  11. T

    DJI IOSD Mini and RMA issue

    PM me.
  12. T

    DJI has released its 2.4G Full HD digital video downlink, the DJI Lightbridge

    I downloaded the new firmware yesterday and the results were great until I upgraded the air unit and got a hardware mismatch error. Oh well I will have a production unit by Friday. What I did notice is the latency is about 50% less than the previous version that I have tested. I can't wait...
  13. T

    P2 Vision Ground Station Owners Tread

    Yes it is true the much awaited GS App for the Vision is about to be released. I will down load the app tonight and post some video and pictures tomorrow depending on the weather.
  14. T

    DJI Lightbridge NEW price tag!!

    It will happen. This issue is with the video in to the iOS. It is not that simple with the Apple products. The android is easier to do this with.
  15. T

    DJI Lightbridge NEW price tag!!

    Just use a second radio for your camera operator. You can set him up with a slave unit for clean video down.
  16. T

    DJI Lightbridge NEW price tag!!

    I have not but they were talking about it at NAB. The new app is now out for the android and works well. I will be getting a production test version shortly and be able to show what it can do. Here is a short video that shows the app and assistant. Sorry for the lack of audio. The only...
  17. T

    Will iOSD Mini work with A2?

    The iOSD mini connects into the can bus for the telemetry. If you feed the video in from you FPV cam to the mini and then to your vTx I don't see an issue as long as you are on 5.8gHz for the video down link.
  18. T

    H3 2D working but can't adjust settings after firmware upgrade

    You are correct. RC Assistant first the Assistant. The Horizontal the Vertical tilt are only for FPV in my understanding.
  19. T

    Motor configuration on a 550 using Naza m lite what's better?

    Have you checked your static balance? Left/Right and Forward/Back? That may be your issue. Have you also check your IMU calibration? I would do the advanced calibration as well. Make sure that when you take off that your copter is on level ground.
  20. T

    Dji A2.....ready to give up I reckon!

    Mine is only 1cm in front of dead center. I have not had issues at this point. My lipos and H3-2D are below the GPS on the AeroXcraft gimbal.
Top