Search results

What about motor and ESC temperature in 5.08? Any improvement comparing to 5.06?

Before upgrade to D550 I was flying AUW 1880g without any problem. Graupners 10x5 and LiPo 5000 4S.

And what about temperature of motors and ESCs? Aren't they hotter then in 5.02? I had such a problem after upgrade to 5.06 and rolled back to 5.02.

I've just added EzOSD with current sensor and downgraded my WK-M firmware to 5.02. Now it flies OK and motors are cold. While hovering total current is ca 37A, so ca 6,2A per motor - far below limit of this motor. :)

Changelog disappeared... Link to older versions points to nowhere... Who's brave enough to try 5.08?

I also had a problem with 5.06. After upgrade from F450 to F550 I've also upgraded firmware from 5.02 to 5.06. Motor load was only 10% higher then in my F450, but motors were hot after short flight (ESC was also much warmer then usually). In third flight my copter was hovering 1m above ground...

Ad. 1. I have Futaba 9C. I've connected it to Wookong Assistant, calibrated and with trimmers in neutral position calibrated each channel using end points and sub-trims, so with sticks in their central position all sliders in Wooong Assistant are exactly in their center position and green, and...

All of them are equally hot. I think I'll buy boom extenders to fit 12x5 Xoars and replace DJI motors with AXI 2814/22 because I like 15min flight time. But still I cant't understand why GGoodrum had the same motors barely above ambient flying 3766g AUW setup...

My F450 was flying AUW 1880g so 10% less per motor and the motors were cold. It was also flying with Graupners 10x5 and 1 x 4S 5000mAh.

I've just finished my new setup: - DJI F550 - WK-M (firmware 5.06) - AeroXcraft landing gear and GoPro gimbal - DJI 2212/920 motrs - Graupners 10x5 - Lawmate 1,3Ghz 1W - EzUHF 8ch RX (awaiting EzOSD) - 2 x Turnigy 4S 5000mah 25-35 C AUW is 3100g (ca. 6.8 lb.) This copter is flying very...

But if it's the same... Acording to mikrokopter.de: "BL-Ctrl Version 2.0: Peak current: 40A -> Peak power output approx. 650W (max. several seconds) " Aerodrive: "Through high performance MOSFET’s (30 pcs per controller) 35A constant or 45A burst (up to 30 seconds) possible" With BL-Ctrl I can...

Okto XL Power board RTF - 719,00 € Aerodrive Power board - 1.459,00 € What's the difference expect price and radiators size? It was mentioned here, that it is the same, use the same software... Of course AeroDrive 8 looks great, but is it a reason to pay double price for it? May be it is better...

I am going to buy HL frame for aerial photo with heavy cameras. Now we have following options for HL frames: 1. Mikrokopter with BL-CTRl 2.0 or Aerodrive or Herkules II limited to ca 35A per motor but with redundancy 2. Wookong-M with PWM ESC in fact without any boundary for motor current, but...

I am looking for a pair of orginal DJI 10x4.5 props (like in FlameWheel kit). Is there any shop in EU offering it?

I just wonder if installing magnetic compas right above motor cables and so close to a motor and ESC is a good idea...

Hi! I am going to build a heavy lift platform able to carry 4-5 kg camera. I found frames mentioned in title of this post interesting (with Plettenbergs 15-20). Is there such a big difference in payload of these platforms? According to information on websites of these product, CS8 can lift 2,2...

Check http://www.aerosimrc.com