Search results

When we use these we cut the plugs off and just keep the 1/8" jack and solder everything else in so i've honestly never checked this before, looking at that chart above, see standard camcorder, that's showing reverse polarity, might be lot of what you have already's problem or gets rid of...

use the top row for the pinout your after, get a volt meter and pinout continuity check to make sure yellow is really the yellow pinout, etc. all you need is video, there isn't usually sound needed so it might be the red or white rca jack that is the video signal,,, otherwise just try the red...

prolinks vsry06mg= http://www.bluekangaroos.com/Luxtronic-6-ft-3-RCA-to-18-Male-Camcorder-Dubbing-Cable--Nickel-Plated_p_8811.html I've bought a few of them at radio shack...

you can get them at radio shack,,,, it's a 4 place 3.5mm stereo a/v cable prolinks vsry06mg that's assuming your talking about the rx side,,, on the tx side i just use standard servo plug on ground, +5v if i need it and vid. the 3 place ones stretch across those 3 pins

I woulda been down that road if it wasn't for sitting here watching these bl burn up randomly and not being very easy to work on.... that and being so low rated of parts as in u5 or smaller. i've flown two cinestars with these on em and they weren't as smooth as i had mine but i didn't set em up...

that's not an ignorant question..... i'll be running both back to back to compare it..... My suspisions are the improved power will negate any mechanical advantage the idd offered but we gotta make sure that power stands up to the real world at work environment. Sounds like smaller motors...

imagine balancing the rig on the ground using one arm, leaning 45 degrees, the opposing arm to the one touching the ground is in your hand...... give a big push to the crash cage, rotate one arm repeat, repeat till all are adjusted. You WILL hear some creaking, normal, just make sure all the...

i assumed he got heavier....... if the battery was the same weight it may take a smaller prop,,,, but short flight, got a new pack, 4s 5000 mah sounded like it grew good call, forgot his gains might need adjusting.

www.bbcamerica.com/earth-night/videos/superhuman-animals/ starts tonight

your maxing out the power, got anything bigger like 10" prop? It's shifted it's hover throttle, most likely higher. make sure where your mounting it isn't shifting cg, pick it up by two opposing arms and then other two, should sit straight and not try pivoting in the palm

imagineers going aerial, imagine the possibilities. theres a permanent notam over disney here in So Cal, see it everytime i pre-flight. i'd imagine that's to prevent loitering fools above, so they already have a pretty clear sky over em here.

We have to build an actor "drone" and when they asked what FC i wanted, picked another superX. Were invading mexican airspace with it....

rf explorers are really nice to have around We went into a rf clean room and got analyzed on a rig, they put off what there operating frequency is, ie, plush tested out emiting 50hz, simonK put out 400 hz...with the big expensive rf instruments

might try ntsc if your pal,,,, if possible. maybe theres a 4:3 and 16:9 to choose, try those. look for stretch versus fill scaling

me too

i get what your saying and i get the industry. what i'm saying is instead of sitting there whoas me, it's pretty straightforward. Theres even webinars on it already and a line of companies trying to figure out how to make all that paperwork that comes with your piper for there fleet of uas. It...

as long as that train of thought is in play, i'll have the whole stage to myself. Nothing there is the case all 8 of us that applied for film exemption are of the smallest a business can get and still exist.... a bunch of ag and flare stack exemptions are there now

recent footage from 8 bit alexmos.... in wind

yea 2nd, go to 1:17, 1:46,

sure has a yaw thing going on there.... needs a third axis if that's as tight as there gonna make the digital tuning