Search results

Yes I can confirm what Gator says. I had a RTH incident . I was at about 200 ft , it returned to home at that altitude, descended to 60 ft ( 20 m), delayed for about 15 seconds then continued the decent to the original take off point. It was awesome to watch.

yes of course. I wired the tilt motor to Aux 2 channel on my Spektrum receiver which is my Knob ( potentiometer) . ( brown wire is neg, red wire not connected, org wire on Tarot goes to yellow on receiver pigtail. Then into your radio settings to your Aux 2 settings ( if that is the channel you...

I have the Tarot T-3D gimbal. Love it. You wont be disappointed.

FYI, the x3 camera that is on the Osmo is the same camera that is on the Inspire 1 Multirotor. You can buy an adapter plate/ gimbal for a multirotor and the x3 snaps onto it the same as it does on the Osmo. I would like to know how the wiring is configure ( if even possible) before I spend the...

Anyone know of a link or how to wire up the Osmo x3 camera and 3 axis gimbal to a Naza V2 with spectrum AR8000 receiver and the video transmitter? I still want to make use of the PID knob on my transmitter for tilting the camera up/down?

Can someone please explain the confusion/ differences in compatibility between " Immersion Rc, fatshark , Diversity, I have a Boscam Monitor. What type is it???? What works with what?? Can you mix styles of antennae on a monitor ( that has twin antennae setup)?? Would you want to?? Can you mix...

I have a Tarot 680 Pro Hex and I have one motor acting up slightly so I want to look into starting to change them over to something more readily available ( something from Hobbyking preferably). The motors are Tarot # TL68po2 4006 kv 620. Can anyone suggest a cross reference motor? Is the Tarot...

Hey Hexatiger, I had my hex take a swim last year as well. Only had one esc go up in smoke after I dried it out but I replaced all 6. Just the thought of that unknown down the road if the others start to deteriorate from the internal corrosion over time and I start to have unexplained failures...

I always balance charge as well and charge at 1c charge rate. I must admit I have taken mine down to 80% a few times. My break in procedures may not have been text book as well. Do you have a couple of preferred brands you like to use.??

I do a lot of video work over lakes doing waterfront properties and would love to find a compact auto inflation , floatation device in case my hex decides to take a swim some day. (which is only a matter of time) Such as the "Water Buoy" http://www.water-buoy.com/ It is only capable of...

Hi Sleepy C, I do have 70% expo on the rudder channel, but I have had since day 1. (this problem is fairly recent) It gives slow smooth rotational speed for panning. When I go to monitor mode on my DX7s and watch the slider it appears to move smoothly and proportionately. Hexacrafters suggestion...

Hi Sleepy, it is not the camera gimbal I am rotating. It is the copter.

Hi Guys. Im trying to do 360 rotational pans for aerial video work and now Im seeing my yaw come to a stop, or halt after about 3/4 of the way around ( 270 degrees). I am holding the yaw stick very smoothly, but it stops rotating after 3/4 of the rotation unless I give the stick a lot more input...

Do you have a more quality charger that brings the battery cells to this tighter tolerance or you just buying better batteries.?? Thanks again for your help.

Hey " Old man" you mean to tell me all your batteries are within 1/10th of a volt?? I have bought new batteries that aren't within a tenth.

Hey rocket man,sorry to hear about your failure. It does make me feel a lot better about my decision to not solder my leads to the pdb. I put crimped ring connectors on all the wires and then soldered them, then made small little aluminum blocks , positive and negative, drilled and tapped holes...

as a general rule , at what voltage difference per cell would you condemn a battery? Thanks guys for your replies.

Thanks econfly. It is a full 1/10 off which doesn't bother too much ,the cells are close enough together in voltage. I always balance charge my batteries, every time. What bothers me is the charger doesn't shut off because the battery isn't reaching full charge. All my other batteries, 3 & 4...

Hi Guys, I have three, 4 cell 5000mah lipo batteries that I have been using for a year now. 2 charge no-problem, the other gets to 16.7 volts and wont go any higher. Even after being on the charger for an hour and a half it wont go that extra 1/10 of a volt or so( the others take about 20...

That's what I did with my Tarot 680. Even though it had solder pads on a PDB, I felt the solder pads could be a weak point , especially on a folding frame. I just took two pieces (one for + and one for - ) of 1/2" X 1/2 " alum. about 1 1/2 " long and drilled bunch of tapped holes to connect...