Search results

mlebret, Many many thanks for that info, have waited a long long time for someone to solve that Jeti arming problem So pl tell me i got it right. 1. I plug in all Jeti ESCs into the zerouav Gemini Controller. Mine is an Octa. 2. Now since i don't have any ESC port vacant, i make ONE Y...

Hi Guys, Need to know if anyone here is using JETI Highcopter ESC specially designed for Multicopters. I have 8 of them, and i have the zerouav E1100 Octa, with Gemini. BUT the JETI highcopter ESC wont arm when connected to Gemini, Tried changing end points, tried sub-trim, tried main trim...

Paktazh, I have Gemini, and i find that also happening. also, each time u put th stick to full and bring it back, the minimum value increases so i did it two or three times, and suddenly my th indication on GCS became yellow, which means idle no idea why it should happen but if that happens...

gerardop i had suspected that cause in all other cases, to take over control by Tx, we have to just change Ch5 to Manual. but somehow they did not mention that aspect in the WayPoint chapter in the Manual

hi geredop i think the Gemini and YS-X6 P are similar in functioning. cause the firmware is the same so i can say for Gemini, in the latest manual on page 45, for Return Home and Land it says " During RHL, the aircraft will not accept any Manual intervention" i guess meaning no control by Tx "...

Hi Multitotorxy8 I am using Jeti HiCopter Muclticopter 40 amp ESCs, and they r opto... super performance but with Gemini controller, they won't arm i have tried putting throttle low end point to 125, then 150, still they won't arm Jeti says, that the low end should be 1.1 to 1.3 milli sec, for...

got email for zero uav. problem of PARA servo sorted out works perfect now. many thanks to zerouav Only one problem or issuer remains... that of American hand not showing on Android GCS Hope zerouav can sort that out also it will be great

vadmcse thank you have done it now, and it has upgraded my GCS i guess...

OK guys... finally have been solving problems one by one, by self learning process... all problems except one sorted out. PARA servo won't work

Hi All. zerouav has just put up a software ZERO-GCS-20140507 dated 2014-05-26 it is and .rar file. What are we supposed to do with it I downloaded it on my Samsung S3 and on the files section, clicked on downloads and then clicked on the files and then on the .rar nothing happened.

guys what is this YS-X4-X4V2-X4P-Gemini-M-S-adaptive-abroad-20140501-Enc Do I need to download this to Gemini also. ???

Cherry Yang, Hi, need some help. 1. I am trying to programme parachute setting I have put Ch 8 on my Tx for Parachute Now when i connect a servo to Gemini PARA output, and operate the sw on Tx, the servo does not operate. I have checked the servo by connecting directly to the Rx Ch8, and the...

Want to congrarulate zero uav on the new Gemini manual v2.3 Very logically presentation of information. Great going zero uav.

hahaha.... this digital world is so annoying sometime. but found the problem it was simple, and i just could not have thought of it.. S3 is not talking to the wifi module Actually, i wish the manufacturers would make the manual a bit more explanatory for the uninitiated lot like me, they assume...

Hi all, I am trying to make the wifi unit link to my samsung S3. I can see ZERO-TECH appear in my mob wifi list, then i click on it, and it shows connecting, and then shows " network disabled because internet is slow". The wifi came preset to PTP mode. So why is my mob not able to hook up to the...

Mike, if u are talking of only operating just Z15, then all u need is 7 channels... however if u have 8 ch Tx that is great cause u can then use all the 8 channels for Z15 that give u control over everything. And for two pilot operation to one or one pilot operation to two, its always about...

I think they have uses 3 ch redundancy only for helix and planes, cause there is only one motor to control. With Multicopter specially OCTAs, with 8 motors must surely be a much of a herculean task. But the way things r going, i guess someone will come out with redundancy even at output level of...

And i am the proud owner of the Z2000 and Gemini controller have fun Ramesh Tahlan

Hi Reginak, I have received my Gemini Controller and Z2000 gimbal a few days ago. Have gone through the manuals. will start the set up once the zero uav Octa reaches me in a few days time But about ur question on Gemini redundancy... its quite simple, it has two GPS/Compass, two IMU, its two...

ProPilotWannaBe Cant thank u enough for this information on how to view data from iOSD thanks a ton. Gonna view in a day or two. doing some work on my table top mini lathe and mill, to make adapters to install the Vibration isolation dampers. Ramesh Tahlan