Search results

one of the feature I like is that the frames are foldable, however in in the past my question has been with support, coming into the frame, if you have any twisting then you may resignate through. I am just curious if anyone on the forum has either purchased or seen one of these up close.

there is always the 900 range, cell phone land

Any one know anything about these frames, if so tap in I am interested in hearing about vibration, and results. They are both foldable and in the past what I have seen in the foldable frames is the lack of support on the arm area. thanks Jack

Topflight, the mast of the copter sits 15cm above the copter, I am not how much matters but i remember when I was building things I read about keeping it as far way from the electronics as you could. I have seen many set up where they are not caring much about those things.

northrnflyer Thanks for asking, its been a little slow mainly I have been pretty busy on some other project and the temps are pretty low these days, but with that said, I have to say things are going very well. The copter flies nice, I had it up the other day in something like 22kts winds...

Here are a few photos from today, I installed the Gruapner props

loaded weight is coming in at 4042g that is with everything, camera, battery, gear, gimbals, motors, frame and longest flight so far on one 6s battery has been 12.5 min however that put me over the drawing threshold of 80% When charging it the battery took 4300mha out of 5000, so when I stepped...

I am not sure for exact by its around 800mm its enough to encounter 15 inch props in wanted.

Boris here is a clip of a zenmuse mounted onto a vulcanUAV frame. It give you a real neat look at well it can handle it all. http://www.youtube.com/watch?feature=player_embedded&v=U30ieERQmPE cheers Jack

that's a good feeling, nice photo

I am lookng for anyone that may have a xaircaft flight controller 1212-s of p either way I am wondering if there is anyone who is willing to dump one for not to much. Like some that I know I had a an x650 however when I figured it could not perform the way I needed it. I then dumped the whole...

more flight results on a fairly cold day, around 38 degrees Fahrenheit I hooked everything up, camera mount, servos, and camera and lift up with a one 6s - 5000mha I did a true 12min flight and never saw my first threshold light set for 21.0 volts. However once landed and charged the battery I...

D- With full disclosure going forward I will probably start helping skyrover a little with some things, one would be the website. Although for the time site is in its development phase I am hoping to clear it up some and start posting some products up there, including the arm kits, and complete...

Here is a vid of the very first flight, sorry I did not have the camera align great but over all you can see how it all went. Over all if flew great, i was very happy with the results. The flight time was basically 8.5 min on a 5000 (6s) battery and when i charged it, it took in 2350mha if I...

ya looking at your post two things stand out to me, one is to check your bullet connectors for corrosion, it so cut them off and put new in place or solder directly to each other. the other look at your motors and see if they are all tight and feel the same as all the others. I had that happened...

Here are some photos of the build, I am just about there. All I have to do is install the props and then launch. The weather here East Coast mid Atlantic has not been the best for flying, So I am hoping the weather will give me a window over the next week. When the parts were sent, another...

weight, I can give you a ball park mainly. I forgot to do it before I sautered the esc's to the board however with that said I was able to get a weight of the whole arm assembled which is 265g After looking up the weight of the motor, that was 188g so if you take away that weight you are...

Ya it all depends on the system, I am a television guy and have been for years. Its all about money on production determines the result. Motocross does not have a lot of bucks behind it so most likely there where not happy because of a few reasons, one being a good configuration to make sure the...

IrisAerial, They are pretty strong and solid, no different in the way the 550 is doing it now, except with no flex in the arms. I have seen them fly and felt them in flight, the vibration seems minimum. Each block matches up hole to hole with the 550 and 450 frames, with the strength of those...

Hey all I am in the start of a hexa build where i am using these conversion booms to make a f550 into something bigger where I can put 14inch props on it. Along the way I have been able to get my hands an new mount from skyrover, Its not quite on the market yet but I know there should be some...