Search results

Chris, you are most likely correct but please note that most of your posting links are not working properly (will not open images).

To answer your question IMHO, the helicopter acts as a large van degraaf electrostatic generator and needs a voltage discharge path so that the workers can step off the helicopter and on to the powerlines without a severe electrostatic shock which could know them out and/or lead to a fall. The...

Actually these have been evolving quickly. Originals came out as kits, then manufacturer/distributor enhanced them by having most pin assemblies installed before shipment, then they added some pluggable connectors and now there is the ARMBGC which simply has all the connectors and cables...

interested in one....depending on price + shipping cost + international charges etc.

IMHO Of the PID parameters, the I and D for the WKM are contained in the advanced tuning section. P - proportional is the only parameter configurable from the Basic and Attitude tuning sections. And there are no options to tune a separate RTH PID loop.

http://news.yahoo.com/faa-warns-public-against-shooting-guns-drones-183617273.html Problem of municipal regulators overstepping their regulatory authority resolved by the following FAA public media statement..... too bad those in Deer Dropping Trail are illiterate.....

Model rocketry hobby has provided a vast range of solutions for cutting tubes and precisely drilling holes in tubes for a number of years.... more recently moving to the home manufacturing of tubing and plate material using carbon fiber, fiberglass Kevlar and other composites..... Just join here...

COG x,y,z It is imperative that you keep the center of gravity with respect to x and y values at the center of your Multirotor.... or some of your motors will be working harder and burn out faster etc. You can shift the z value up and down in accordance with the weight and position of your...

or you might want to send in an old dilapidated MR and hover it over a gas spill and let them shoot away...........

http://www.bigredbee.com/beelinegps.htm Please fly safely not only to protect the hobby but also the general public.

I was encouraged by a lot of participants to bring along my 800mm Hex c/w GoPro3 Black to get some aerial videos of the annual Rock Lake HPR - High Power Rocketry event.... Regretfully closeups of the rockets and pads was not allowed as a result one an overzealous intrepretation of the event...

tremendous work....

If one has the IOC functioning properly.... switch it to Home lock mode.......even if the MR is constantly spinning...... a pull back on the stick will bring it back to you.... Also some of the less expensive park flyer RC radio systems will not have the range you might expect.

Buy Sunnysky motors........ absolutely nothing wrong with the DJI NAZA........ but all RC receivers, MR controller and their sensors are prone to big issues where there is vibration including fly aways... But the biggest reason is a failure to configure the RC radio system to correctly...

EastCoatJib....... thx 4 the valuable tip...... couldn't understand why RTH did not work for me last night..... I had moved the IMU forward and down onto the antivibe mounting position and therefore had to change the x,y,z for IMU position. Seems to me though that a small change in flying field...

Nearly all issues will be with the RC transmitter configuration..... Search for Jon Desjardins Futaba Transmitter and NAZA setup videos on Youtube using the Futaba T8FG Super and you should get most of the answers for your Futaba 14SG. I had similar problems but discovered that my trainer...

Go with the carbon fiber tubes but start out with fiberglass reinforced plywood or G10 plate until your prototype is revised to a rollout stage.... Once the rollout units are flight proven to your entire satisfaction, move carefully up to DragonPlate materials such as carbon fiber laminated...

You might be able to call up the specs on the 50 ohm coax of choice to determine dB loss per foot but most of the dB loss occurs at each connector (the fewer the better). Best also to put heatshrink over the connectors as the insulator between the center wire and the shield typically absorbs...

Buen día. ¿Cómo estás? Yo no hablo español... I live in Canada so had to do a quick search.... UAVProducts phone number will point you towards the state his business is located. I suggest that you contact Robert Remund at UAVProducts here..... http://www.uavproducts.com/contact-form.php then...

Correct me if I am wrong but here is how I understand the recent addition of not one but two new NAZA controllers..... 1) The original NAZA M-GPS can be considered as V1 (version 1) which is easily firmware upgraded to full V2 functionality. 2) All V2 peripherals are completely compatible with...