Search results

Thanks all!! Some of those are 60A and that's too low for me and I'm not so sure on the "solder pads". Has anyone used anything with solder pads on them versus holes you can run your wire through, bend and then solder? That seems like the ultimate hold to me.

The GPS unit will only help you hold your position, track in a straight line and enable the return to home feature given your radio supports failsafe. You FC should not move at all and in a perfect world should always remain pointed straight ahead and never move a bit. The Naza is prone to...

If I were you I'd pass on those motors, 206W isn't going to get you much. You're in the right area if you're building a 4-5lb Y6. Remember with a Y6 you lose major efficiency in the co-axial motor setup. Look for a more powerful motor and I'd also recommend the Turnigy Plush 40A instead of those...

I've never used anything but NTM Turnigy motors and I have yet to have one fail that wasn't my fault. I have over 60+ YouTube videos around 8-10 minutes each and they are all on the same motors, about 15 hours of logged flight time. I hear that but I don't know where it comes from, I can at...

That thing is as smooth as glass man...dang... I guess after you build a couple HUNDRED you get that good at it :) "Sell them to friends so I can still play with them..." You make me SICK!!! :D :D

I'm going to be building a UAP-2 Y6 copter starting this week. I'm having some trouble finding a suitable power distribution board. I need to be able to pull 20A max through 4S batteries though it, maybe 1200W maximum and 900W sustained again on 4S. What's everyone using? Thanks!

Yes, I'm going to re-use what I have on my Hexa. All I'm doing is transferring everything over to the new Y6. I've found through testing that I really like slower spinning, higher torque motors. I'll be using the Turnigy NTM 750Kv 265W motors with either 11" or 12" props depending on what I can...

Kloner, WTH man? LOL, how many multi's do you have now? Are you creating a clone army or what? Kloner wars...coming soon. When you going to sell some of your others? And while I have your attention, what power distribution board do you use and love? Looking for 100A-ish max with 6 or more ESC...

I halfway agree with you because over land at least you can recover it and believe it or not some parts will be just fine, over water...you're toast and it'll be in Davvy Jones locker lol. I'm not afraid to fly over water as long as I've tested it out over land a few times first. If you notice...

Yeah I do however I fly everywhere and there's a huge rush I get from flying over the water lol...I love seeing the water from up high and seeing the sparkles off of it from The Sun. I especially love when birds launch below me and I can fly behind them and record them. I have one video where...

Did you watch the video? That's exactly what I had to do. I had NO luck moving through 45mph air...at full tilt I was moving about 10mph which makes sense since my GPS records speed over ground and my max speed is 55mph. The problem was that I was pulling HUGE amounts of power just to move...

Ah yes, the package...LOL I'm seriously done with this thread. Don't even bother, I'm not responding to any more of this ignorance. Clocks spin clockwise, if the blade produces lift by spinning clockwise then it's a clockwise blade that's all I'm going to say....I'm done.

Actually, I looked up the price so those aren't going to work. They're like 60 Euros each so I'm going to keep looking. Do you know of any others that are high quality that are maybe $25US or less? I currently run Turnigy NTM 750Kv 265W 3S-4S motors...here they are...

If the package determined the way the blade spins, you'd be right LOL. I think it's hilarious that people are focused on the printing on the label instead of the raised portion of the leading edge. This is getting ridiculous and again it's not up for discussion. It's like saying birds fly...