Search results

Kloner, is there any way of mounting those cases on tripods? If so, how? It's the only thing preventing me from building one myself.

I agree with Kloner, either power from the Futabas' battery or power from external. Don't do both. Kloner, I've only ever used the EZUHF with 8 separate servo leads, never used it PPM. On my setup I haven't had to use sub trims but have used expo and it has worked as expected, no problems at...

Keep an eye on your tx if your powering directly from the futabas battery. I set up mine on a 9c and it worked flawlessly for two days, then the tx screen started getting dim rapidly as if it was running out of power. I charged the battery and tried it again. The 9c has not worked since. I...

Yeah, you need to set the TX failsafe so that the RX knows to "flick the RTH" switch when it looses signal. There should be a guide somewhere on google to tell you how to set it up on your futaba, or in your manual. Normal procedure is to set the controls to where you want them in the event of...

Exactly the same problem for me. I'd be interested in any fixes. Also having problems softening the movement when starting and stopping pan

.....and now there is a 5.14a beta. I give up

There is only one hole as far as I know. It allows air in for the pressure sensor to work out/hold altitude

8 servo leads

For me, it wasn't strictly plug and play as I had to make my own lead to link the EZUhf to my JR11x. Other than that, yes. I have been using it traditionally though, haven't tried PPM. All of my leads are hidden away so I'm not too bothered by it. Set all your sticks/switches where you want...

I've been flying a wkm heavy lift octo on ezuhf (traditional) for just under a year and it has performed flawlessly.

Excellent news. Please keep us updated on how it performs over time.

I had the same problem. Try installing 1.1.6 firmware using the 1.1.3 software. That fixed it for me. Adjust the center tunes until the servos stop spinning and save it quickly before they begin spinning again ( I presume these are the 'values', it was roll that was messed up on mine). Then...

Is anyone flying 5.12a on a flat octo with a traditional RX? If so how is it performing? I'm on 5.06 at the moment and am happy but would like to update. There was a thread on here a while ago with someone testing this config and they said that it was ok, but it was early days. I'm just...

What case are you installing this in? I've been pricing up and planning something similar myself. Was planning on a Pelican case

So, after a few cycles these batteries are still averaging around 1.3 ohms per cell on a full charge, have no puffing, and are still taking 95-100% of their capacity. Can I deduce that they are safe to use as normal? I was sure I had damaged them as they were 16.3-16.6v after I landed, and...

Performance in wind is completely reliant on the flight controller/IMU. The dji is not good with large frames and wind. The Only way to get good performance in wind with the wookong is to under-prop it to achieve a higher disc loading. My 6kg ad8 flys excellent in high wind with the wookong but...

I have the AD8, and am very happy with it. It's a solid kit. I've never flown or seen a Cinestar......however, the Cinestar models look far FAR cooler!

All of you guys getting the jitter, are you only getting it when the gimbal is on the deck or are you getting it in flight also? I have jitter (slow slight rolling from left to right) when the gimbal is on the ground but I don't notice this at all when watching back flight footage, it all seems...

Ah, no worries man. I only said in case you had missed it and wanted to watch the vid. Wasn't meant to sound hostile =)

I posted what I did a page or two back with a video. Basically, made sure all my belts were tight and added two felt washers to each servo. Running 1.1.7. Get slight twitching when it's sat on the deck but not when it's airbourne. I also balanced the payload