Will This Build Work?

[Sam Fox]

Will this build work with the parts in this list?\

• Turnigy TGY-i6 AFHDS Transmitter and 6CH Receiver (http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=74037)

Turnigy TGY-i6 Transmitter Specs:Frequency: 2.4ghz ISM Frequency RangeModulation: GFSKSpread Spectrum Mode: AFHDS 2A and AFHDSBand: 142Number of Frequency Channels: 20Output Power: <=20dbmWorking Current: <=100mAWorking Voltage: 1.5v x 4 AADimensions: 174x89x190mmWeight: 392gResolution: 1024 bitStick Mode: Mode 2 (Throttle Left)

Turnigy iA6 Receiver Specs:Channel: 6 Frequency: 2.4g ISM Frequency Range
Power: 4.5V~6.6V/<30maNet Weight: 6.4gDimensions: 40.4x21.1x7.35mm

• Afro ESC 20Amp Multi-rotor Motor Speed Controller (SimonK Firmware)
  (http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=67935)

Current Draw: 20A Continuous
Voltage Range: 2-4s Lipoly
BEC: 0.5A Linear
Input Freq: 1KHz
Firmware: afro_nfet.hex
Discharge wire/plugs: 16AWG/Male 3.5mm
Motor wire/plugs: 16AWG/Female 3.5mm
Weight: 22.8g (Included wire, plug, heat shrink)
Size: 45 x 25.7 x 10.5mm

• Hobbyking SK450 Glass Fiber Quadcopter Frame 450mm

(http://www.hobbyking.com/hobbyking/...ber_Quadcopter_Frame_450mm_US_Warehouse_.html)

Specs:Width: 450mm
Height: 80mmWeight: 300g (w/out electronics)

Required:4 x 28mm 1000~1200kv (or similar size/kv)
4 x 15~25 Amp ESC
4 x 8x4~10x4.5 Prop (2CW & 2CCW)
1 x HobbyKing Multi-Rotor Control Board
1 x 1500~2200mAh 3s 11.1v Lipoly battery
Your own radio and 4 channel receiver

• Hobbyking KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA
  

(http://www.hobbyking.com/hobbyking/...th_6050MPU_And_Atmel_644PA_US_Warehouse_.html)

Specs:
Size: 50.5mm x 50.5mm x 12mm
Weight: 21 gram(Inc Piezo buzzer)
IC: Atmega644 PA
Gyro/Acc: 6050MPU InvenSense Inc.
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us

• NTM Prop Drive Series 28-26A 1200kv / 286w
  

(http://www.hobbyking.com/hobbyking/...Series_28_26A_1200kv_286w_USA_Warehouse_.html)

Specs:Model: NTM Prop Drive Series 28-26A 1200kvKv: 1200rpm/vMax current: 17AMax Power:215W @ 12v (3S) / 286W @ 15v (4S)Shaft: 3mmWeight: 57.6gESC: 20ACell count: 3s~4s LipolyBolt holes: 16mm & 19mm
Bolt thread: M3Connection: 3.5mm Bullet-connector
Prop Tests:7x6E - 11.1v - 90W - 8A
7x6E - 14.8v - 192W - 13A
8x4E - 11.1v - 100W - 9A
8x4E - 14.8v - 222W - 15A
8x6E - 11.1v - 145w - 13A

• Turnigy 2200mAh 3S 20C Lipo Pack
  

(http://www.hobbyking.com/hobbyking/...y_2200mAh_3S_20C_Lipo_Pack_US_Warehouse_.html)

Spec.Minimum Capacity: 2200mAh (True 100% Capacity)
Configuration: 3S1P / 11.1v / 3Cell
Constant Discharge: 20C
Peak Discharge (10sec): 30C
Pack Weight: 188g
Pack Size: 103 x 33 x 24mm
Charge Plug: JST-XH
Discharge Plug: XT60

• Turnigy E3 Compact 2S/3S Lipo Charger 100-240v

(http://www.hobbyking.com/hobbyking/...o_Charger_100_240v_US_Plug_US_Warehouse_.html)

Specs:
AC Input: 100~240V, 50~60Hz
Battery Type: LiPoly
Cell Count: 2~3 Cells
Charge Current: 1.2A Max
Cell Cut Off Voltage: 4.2V ± 0.02V
Circuit Power: 11W ± 10%
Dimensions: 88x57x35mm
Weight: 103g
Plug: US 2 Pin Plug

• 10x4.5 SF Props 2pc CW 2pc CCW
  

(http://www.hobbyking.com/hobbyking/...Props_2pc_CW_2pc_CCW_Green_US_Warehouse_.html)

Length (Inch [X]) 10
Pitch (Inch [Y]) 4.5

If I get these parts, will they work together? Will I need anything else? I am also confused on how to get the 11.1v battery to get down to the 6v that the controller needs. Any help is appreciated.

 

[eskil23]

I think those propellers are too large for the motors. Check the spec for those motors. I would go for 920-980 kv motors for a frame of that size.