Search results

Unfortunately I could not find tarotrc official support. The GS is very good, but I need a stabilizer off completely. take-off and landing of the problem. I drone legs are weak and easily at any vibration on the ground. Mode2 only off the pan servo. Ideal solution: No power off, only...

Hi George Can I help you for your wesbite maintenace? I know with Joomla! octomovie.com

Thanx George. Its great. when there will be a new fw? njozsef

Hi George. Thanks for your reply. Own problem again: I planned the wireless serial setup for picloc, but i not found good solution the 9bit "jetibox" 1 wired wireless system. I would like to ask if you develop picloc that raw TxD-RxD serial to data-port1 or 2 on the picloc. Then it would be...

Graham, Thank you. OK. Wired jetibox now it works. Jetibox is 1 wired serial port (same wire to rx/tx data) This is my problem. How to connect this 1 wired serial data to wireless rs232 transceiver I found the diagram from mikrokopter. RX/tx with bridged this diode. This solution how adapt the...

Hi all I ask again. How to make wireless serial connection from picloc3x and PC or jetibox. All working solutions should be. Diagrams, etc. Thank you. Jozsef Nagy.

Yes. My picloc it used to be inner-axis. 4 pieces Savöx servo burn out :( Many other problems as well. I went back inside only z-axis.

please help me. I need a wireless connection between picloc and jetibox. If you can send diagrams How should the serial 1-wire mode to connect? transmitter modules: RFM-22B (868Mhz) http://www.sparkfun.com/datasheets/Wireless/General/RFM22B.pdf thank you

Please help me. I not found the good working picloc V55 firmware and tools on the rotorpics website. Thank you. Jozsef Nagy

I testing today the unallowed 57.15 testversion for big octo, all 3x360 servos. Cinestar gimbal GOOD-GOOD-GOOD. Thank you George. I wait the final version. Good job!!!! Working the more 90 degree tilt. :-) putative bugs: roll neutral position different the stabilized and non stabilized mode...

Sorry..... :upset:

I found the big internet: http://www.rotorpics.com/p3xv57/release_notes.pdf

I have no right to it. But if you'll find clever

something begins :)

Hm-hm I translated google (from english). Now I do not understand :nevreness: So. All 3 ACC sensor is used gravity sensor. Absolutely good from measure gravity vector, but slowly raction time (more secundum). Gyro is fast but drifting, and if rotated the measuring angle to close 90°, then...

Hi all. I solved the ROLL drifting for V56. Picloc very sensitive the geomertical regularity. If not parallel the picloc plastic edge-x-axis the gimbal-x-axis and/or y, the picloc corrected x axis while error occurs the other axis. Results: ACC corrected x axis and 2-3 sec correcting the y...

Hi all Please send link the picloc toolz v053. I found the "2011-12_04_P3XPRO_v053_STD.HEX" firmware but not working the 055 toolz. Thank you

Hi George. I found the interest problem (?). If ROLL function not checked SKEW checkbox, then NOT used the acceleration gain parameter. (maybe smooth parameter too) (i used roll direction fine-controll by POT on transmitter). Solved problem: checked the roll skew and designated the aileron stick.

Hi all The picloc horizontal stability problem witch fw. normal or 3xgain version? (or all newest?) THX

Hi. I tried ACC calibration on Picloc toolz 3x 0.56. But only passed ACC calibration, if checked the "auto accelerometer calibration on startup" checkbox.