Search results

Hello ! I have a bluetooth datalink from my NAZA. When I power up the ground datalink, the link led is solid green. the TX/RX led blinks red. The bluetooth led blinks green. When I try to connect to the bluetooth from my ipad in the settings, the ipad does not find the dji bluetooth. I have...

Hello ! I do a liftoff with the TX in GPS/ATTI and IOC. When I switch to the joysticks on the IPAD the IOC is automatically switched off. How can I prevent the copter from switching off the IOC while I use the joysticks on the IPAD ? Fritz

Hello ! I have one question : If I connect with the IPAD ground station to the copter, are the joysticks of the radio transmitter disabled or can I fly either with the IPAD "joysticks" or with the transmitter joysticks ? Fritz

Hello ! I have 3 complete sets of 2.4 datalink modules. Only one specific air module talks to one specific ground module. ( They have numbers printed on them ) I would like to use only one ground module and talk to all of the air modules. ( only one at a time ) I have 3 copters and do not want...

Hello ! I cannot find the page alt DJI where I can download the assistant software. Please help. Fritz

Hello ! Is ist possible to connect a can-bus hub to the PMU V2 so that I can connect all : H3-2D gimbal BTU module iOSD mini ??? Fritz

Hello ! I have tried to connect the ipad ground station over bluetooth with WKM bluetooth LED module. IPAD odes not recognize any bluetooth connection. firmware : 5.26 Did anybody already get any connection ? Fritz

Hello ! With this tool you can update datalinks and bluetooth module. When I connect with USB to the bluetooth LED or WKM with the tool the assistant shows that there is a new firmware. But when I click on the ne firmware it says thet with this connection there is no update possibility...

Hello ! I have a problem since V 5.24 : When I want to start the motors all begin to spin very slowly. But when I put the stick to middle position and more to take off some motors will stop. I have already set the idle speed to "high" I have to stop the motors and try again and again. After a...

Hello ! I have a Quattro NAZA V2 Copter with 1.5 kilo and 3 Cell LIPO. When I take the parameters that are written in the manual of NAZA the copter is much too nervous in the air for nick roll and yaw. Can anybody reccomend parameters for my confiruaration ? Thank you Fritz

Hello ! My configuration : S800 WKM 5.22 Zenmuse Z15 with Sony NEX-7 The problem is : When I rotate horizontally the copter in the air, the horizon of the zenmuse drifts ( tilts ) away. When the copter stops rotating the horizon gets horizontally again very slowly. With the firmware 5.20...

Hello ! I have a big problem : My NAZA is working ok and flying is also ok. The LED shows the status ok. But when I connect the USB connector the led stops showing the status and gets green with very low light. I cannot get a connection to the PC. This happens since yesterday. Befor that I...

Hello ! I have a very bad video picture on my groundstation. nearly no color and the contrast is too much. It is not a problem of the downlink or the monitor. I already checked it with an pal signal on the downlink. So the video signal out of the zenmuse must have bad levels. It has a V2...

Hello ! I want to use a JETI receiver with its PPM output with WKM. Has anybody experience with this configuration ? Does it work as well as the Futaba receiver with S-Bus output ? Fritz

Hello ! I already contacted DJI about this problem : When I connect the LIPO the the copter after a while there are three white flashes. In the manual they say : attitude status bad. ??????????? This happens before i start the motors. What does that really mean and what can I do to eliminate...

Hello ! I have a Zenmuse and a Sony NEX-5. They work together very well. Now I got a Sony NEX-7 for the Zenmuse. They do not fit together : - The NEX-7 is flat at the bottom and does not fit into the plastic where the screw goes trough because the plastic is not flat ! With the SONY NEX-5...

Does anybody alread know this ? http://www.kopterworx.com/Kopterworx-NEWS/new-s800-antivibration-upgrade Fritz

Phantom with Graupner e-props 8x5 and video downlink.

Hello ! I have 2 WKM kopter and at each the same problem : Temp inside : 20 degrees centigrade. Temp outside : 1 degree centigrade. When I take the copter from inside to outside everything is ok. No white flashes and I can fly. After the first fly the copter stands still outside for appr. 10...

Hello ! Can anybody tell me what the difference between those two is ? One thing is that NAZA can only handel HEXA and not OCTO. What else ? Fritz