Search results

I have up for sale my trusty Cinestar 8 360. It was purchased in 2012, It has been flown many a shoots for me with no question or complaining. It will include the following with the sale: FreeFly Systems Cinestar 8 360 RTF FreeFly Systems 3 axis servo gimbal - no stabilization included 8x...

Sold the MK board, the rest of the gimbal is still for sale. Price reduced to $1000.

Yes both are still for sale.

All were stock on the copter when I purchased it. They have never been crashed or landed hard. I have 8 spare 450mm booms - Cost new $720 - $320 for all I have 8 Quadropower QC3328 Motors Cost New $736 - $450 for all. Info on them HERE I've also got 8 motor mounts - Cost New $424 - $200 for all...

I am unloading my Cinestar 3 axis gimbal ready to fly with a MK FC 2.1 already mounted and tuned up. I have used this gimbal for many shoots with great success. The FC is used as stabilization and control of the gimbal. It is pre-soldered with an S. Bus inverter and all wired up for a 3s lipo...

Sorry the navi and GPS are not for sale. Only what is listed here is what is for sale.

Prices lowered. Okto distribution board $400 Flight Control's $200ea

I have an ESC loaded power distribution ring for an okto. It comes already addressed and ready to go. It has a single EC5 connection if you want it. Sells new for $794, I'll let it go for $600 shipped in the CONUS. I also have a FC2.1 that has been flown in the same Cinestar 8 with no...

Has anyone done this? I'd like to switch over to 6s lips on my Cinestar 8 and convert to a heavy lift frame. I have been looking at some 6s HL motors and have been liking the specs. I am tired of the 4s packs and everything else I have uses 6s packs. If there is a mod that can be done I am more...

Bump price drop - $325 shipped CONUS

Shot this while I was on vacation in MN over Thanksgiving. Enjoy it!

i just found the photo album with all of your MK settings. I see you have the under voltage set to 14.8 which is too low it's set to the nominal 3.7v per cell. set it to 14v(140) or 3.5v(35) I've had good luck with this setting. Does the Roll of the kopter feel like it's too twitchy or...

MK Parameter settings Summary I found the setting breakdown and a summary of what each setting in the MKTool software does. It took me a while to find it.... send me an email and I'll send it to you. Or try this LINK

I too have had the same thing happen with my CS8. My motors will start and not accelerate past much more than an idle in cold temps. I looked through the MK software for hours and couldn't find any temp setting. I now just let it warm up the motors and the BLs and then shutdown and immediately...

I'm using a TP 820CD and a Hyperion 1420. The TP does a bulk of the charging. I use the 1420 for finish balancing. I have on order a FMA PL8. I should be able to bring 6 packs up at a time - then finish balancing on the 1420, but that depends on how accurate the PL8 balances. I also plan on...

bump

I'm with aviator. I'll charge my packs up the night before a shoot. I usually use all of them up and have to charge a few onsite but I always will discharge them if I do not have anything for a few days. My new charging station will allow me to charge 4x 6500s in about 15-20 minuets.

I'd say it's more of a safety thing. A fully charged lipo is much more volatile than one that is at half it's capacity. I've been far too anal about battery storage and cycling. I generally will charge my batteries to capacity the night before a shoot and then make sure to fly them all out. Then...

bump.

I have a nearly new MikroKopter Flight-Ctrl 2.1 that is about 2 months old and has very low time on it, maybe 20 flights. I was using it on my Cinestar 8 for stabilizing the 360 gimbal, I've moved to the Radian system and no longer have a use for the board. It currently has a S.Bus inverter...