Search results

Selling one of my spare Mikrokopter Okto XL Power Distribution boards. I had pulled this from one of my X8's a little over a year ago because BL-Ctrl #6 started acting up. Sometimes it would be fine and other times it wouldn't initialize, meaning it gave me an I2C error. You can see in the...

Letting this go for $500 and I cover shipping in CONUS http://www.multirotorforums.com/showthread.php?14642-QUAD-for-sale-Rusty-s-Frame-MK-(v2-1-FC-amp-NAVI-GPS)-with-extra%92s

Howdy, Anyone tried one of these repeater systems yet? I really like the idea of this to use with my Graupner system. I also like the fact that I could put it up in a tree when flying in forested areas and not actually have to be in the tree myself to fly...

Selling my like-new Panasonic GH2 14-42mm kit with many extras. Its just more camera than I need and therefore hasn't been used much. This is a much sought after camera for video now that the firmware has been hacked. Includes (with original packaging): Panasonic GH2 body Panasonic GH2 14-42mm...

This quadcopter is bind-and-fly with a Futaba transmitter and 3s/4s battery or ARF with your own TX/RX combo. This is a Rusty’s frame (aglhobbies.com) quad with carbon fiber arms and includes Rusty’s simple vibration isolation plate for a hard mount GoPro camera on the front. The motors are also...

I was just checking out the MR cube contest over on diydrones.com. "TO ALL AQ PILOTS. DIY Drones has a challenge to pilots to have there aircraft fly a 50 meter cube that is 20 meters above the ground." - from the autoquad forum This was generated from the GPS log file. WOW! There are...

Just curious how many are using or have tried out the Autoquad 6 flight controller? Would love some opinions on ease of setup and use, primarily compared with MK. It looks like it has a ton of potential, especially for waypoint navigation and autonomous flight features. Thanks, Shawn

Found what I needed!

Found what I wanted!

I have been using my CAMremote as an intervalometer with my GH2 for a long time now. I am now ready to hook it up to the FC so i can have it trigger at waypoints and with a switch. Below is a diagram of how I have it wired up but it is not triggering. I am using the setting Manual: RC receiver...

I have designed some parts which I had a buddy cut from G10. I would now like to have some of the same parts cut but from carbon fiber. I am mostly going for an increase in rigidity along with weight reduction. I can provide .dxf files and have the cf sheet sent to you. It would just be a single...

Hey all, Been looking at getting a set of heat sinks for my other okto distro board but wanted to get some opinions about which ones to get. I have found them at three different sites and all the pictures are different so I am not sure which is best and they are a range of prices. $14.99 set...

SOLD!(8x) RCTimer BC2836-11 750KV Motor's w/ better prop adapters - $75 shipped CONUS SOLD! I am selling eight (8x) RCTimer BC2836-11 750KV motor's with original prop adapters and two different types of much better prop adapters. There is a set of 8 smaller prop adapters and a set of 10...

SOLD! (5x) DYS A3536-11 750KV Motors (same as RCTimer 2814-11)- $70 shipped CONUS SOLD! are 5 - DYS A3536-11 750KV Brushless Outrunner Motors short shaft (same as 2814-11's) 4 of them were flown for a total of 10-15 flights and still have the leads on them, the other one is new in box. These...

Well, I guess it had to happen some day because I grew careless. I lost my FPV quad yesterday because the battery went dead on my MX-20 transmitter. I had just finished finally getting this copter exactly how I wanted it and away she went. I watched about $1200 fly away while yelling at my wife...

I have tried several ways to program my Graupner MX-20 to start the timers when the throttle is beyond about the 15-20% position. I normally have one timer count up from 0 and the other count down from about 10-12 minutes so I know when its getting close to time to bring her home. I had no...

Hey everyone. I am curious of the GH2 settings used by others for video from their copters. I can get it to take great pictures but I am just not happy with the video I am getting. It would be great if someone would even provide a little tutorial of what they do. I need to know things like if...

Snap Quad frame with extra arm/leg and center plates - $30 shipped CONUSA I bought this frame a while back thinking I wanted a small little quad to fly. I flew it a few times but I didn't have the right motor/prop combo and didn't feel like spending more money on it. It has very few flights...

SOLD!: Heavy Lift Y6 Ready-To-Fly w/HoverflyPro FC and Futaba T10 plus many extras SOLD! I am selling my Heavy Lift Y6 to help fund a new project. Originally this copter was a hexa that I converted to a Y6 for redundancy purposes. I rarely fly it because I mainly use my MK X8, the Y6 was a...

Hey Guys, Thought I would let you know about a great sale on the Aoyue 968A+ Soldering station that I just found and finally purchased one! Very excited to get this. Its on ebay for $143.10 with free shipping from Top-rated seller...