Search results

Just noticed on the Gremsy site they have a gstabi 6 "coming soon". Could be interesting. Anyone have any inside info? Release dates, price etc?

When the motors are not hooked up? I'm waiting on an order to install them but I did power up the FC and configured it on the PC. All I'm getting is a fast red.

I've attached a pic of how I've wired it. I have a fatshark 600 line fpv camera. Jumper is removed (nstc) Immersion 600mw vtx. I am getting osd info displayed on fpv monitor but no picture from the camera. I have verified settings in superx software. Camera 1 and nstc. To be honest I've...

Im using sbus from my Superx FC. I assume that go directly from the superx to the sbus on the receiver, not sbus2. Reading the manual here and not understanding the difference between sbus1 and sbus2. Also. if I use channel mode D, Channels 9-14 on the transmitter will control servo...

On another forum guys are raving about the cellpro 8. What is your favorite. I am looking for something that do 6s10000, 12000, 16000 fairly quick. I have a 60 amp @ 24v power supply. Also, I have seen they use a squid to charge a couple batteries (same cell count) at once. One...

Quick questions folks. 1) is there any problem having the auto pilot stuck to the I/O like this 2) I had to extend my esc wires to reach the I/O. I used the servo wires that came with the superx. The may be a gauge lighter than the KDE wires. Any problems?

Lets say I want to control camera pan and tilt with the main controller (14sg) but also be able to switch to a 2 man setup. This wont be done in the air. Changes can be made on the ground. I know some of you guys have done this. What is the best way? thx

I was looking at these batteries. http://www.genstattu.com/tattu-25c-10000mah-6s1p.html They have the typical jst balance plug and highlighted in red it says "discharge plug not available". What is a discharge plug? I thought most chargers discharge thru the main plugs. Also, is there a...

I'm using a 14sg with the 7008 reciever and shown here: http://www.gpdealera.com/cgi-bin/wgainf100p.pgm?I=FUTL7675 So I use sbus to connect to my xaircraft super x. Then everything else, light switch, retracts etc can plug into the servo inputs on the reciever? Is that correct? Thx

Will the sbus from my superx I/O be the power source for my reciever? Thanks.

http://www.cnchelicopter.com/xaircraft-osd-for-superx/ http://www.cnchelicopter.com/xaircraft-osd-v2-for-superx/ I'm having a hard time understanding the difference here. One less input but 2 inputs on 1 cable? That's the difference? Thx

Does it matter if I power the I/O with 6s power direct or 12v off my bec? Thx

Are you guys mostly using 2 x 12v server power supplies in series? Lots on ebay for sale. If you are good with this stuff could you post a link to a good one to use on ebay? Thanks.

Let's say I pick a slightly larger motor than I currently require with the thoughts of using a larger camera in the future. Let's say with the current setup it gives me a 35% hover. Is there any downsides to that? Thx

I have a gryphon PDB for my hex build. It's rated for 260a continuous or 320a peak. Being a technical guy I've looked into the specs which tell me it has 2oz copper. So I looked into what that means. It basically means 1 sq' of said thickness weighs 2oz. As far as how thick it actually...

In the 10000-22000 sizes what battery do you folks prefer? Is their a specific brand you have had better luck with? Also, what charger do you like for these? I was all set to buy a cellpro but just read a battery showdown tonite ranking it 6 out of 6. Damn internet. Lol. Thx

Yes. Very dumb question I know. Correct me if I am wrong. I want my gryphon build to be set up for one or two man operation. This post is about my main controller. There will also be a second camera tx. Xaircraft superx fc. Hex Gimbal tbd. 4 Channels to fly, 1 for course...

Still in package. $40 + shipping. Located in canada.

Probably 6" long. High intensity In both red and green. Good quality with aluminum heat sink if necessary. 12v. Preferably in Canada but open to other suggestions. Any ideas? Thx.

Withdrawn.