Search results

I have two of these..... one lasted for about six months then the 12 VDC out failed, green LED switched to Yellow LED but the fan still runs...... Anyone know what the yellow LED indicates and how to fix it?: sooo... I switched over to the other one which lasted about 3 weeks.... then there was...

These are very complex and finicky machines requiring a lot of technical savvy especially as you move up to the larger systems. Starting small and cheap allows you to learn and practice with minimal downside..... fixing a Blade MQX costs only pennies...... fixing a system c/w costly camera can...

Did you try again with the Yaw gain turned down a bit? Was there a camera payload c/w 2 or 3 axis gimbal control?

Actually you don't need to calibrate the GPS but there is a digital compass inside the same housing which needs to be calibrated..... First determine the angle of declination from true north for your flying site...... The rest is in the DJI documentation......

Thanks....

Seems the most obvious distinction between the Cinestar 8 and Cinestar HL is that the HL comes c/w with a FreeFly Systems power distribution board c/w esc programmer that connects to a single point on the distribution board. But I am curious how that can provide a more accurate and robust...

Exceptional Really enjoyed your show reel........ outstanding work. Can you also indicate where you obtained the gold or orange anodized FPV bracket mounted on your Futaba transmitter? [ QUOTE=ssjheli;125583]My new Showreel. http://www.youtube.com/watch?v=GKGXKMISlI8. Søren Jørgensen Rotorcam.dk

Bruno..... if you dig through the following all the way to their online pricing you will see that they charge quite a bit more for CNC machining of carbon fiber plate. This is because CF plate is considered one of the most difficult of all materials to work with.... dulling and burning out most...

Excellent. thanks for sharing.... worth serious consideration versus a dedicated IR camera which has a more limited IR spectrum.

Mike and all.....Here is another forum that does a good job comparing MikroKopter with DJI WKM on the Cinestar 8 HL etc. http://www.mikrokopter.us/wookong-heros/wookong-m-on-cinestar-frame/

Please note that your hotlinks to freeflysystems forum are not working.... Please resend if possible. Which power distribution board and ESCs are you using? I assume freeflysystems......

ANy chance you can provide name of buyer for me to contact and/or send me some photos of your Cinestar 8 setup?

BTW..... Do you have any photos of your build? I also have a Cinestar 8 and am wondering how and where you are locating your IMU which is apparently prone to MR frame vibration and baro prone to prop wash such that DJI since released an anti-vibration kit so as to relocate the IMU away from both...

Has anyone on this forum been able to successfully install the WKM and fly it on the Cinestar Octocopter? Seems the WKM IMU needs to be mounted on the DJI anti-vibration platform to work properly but how would one achieve this on the Cinestar 8? Here is some...

http://www.youtube.com/watch?v=L3DmZAx0bdQ:livid:

Excellent. My Hyperion reads 15 milliohms for all 6 cells.... used to be around 12 milliohms per cell..... Turnigy Nanotech..... roughly 50 recharges so far.

I am hoping there is a simpler way to determine when to retire the LiPos on my MR. Is there a direct correlation between battery line loss and battery internal resistance? If so I am hoping to gauge battery retirement by means of the later. The DJI method for retiring batteries requires multiple...

Are you saying that you strip new motors and boil the bearings in synthetic oil?.....

I personally would never fly my MR unless I am certain that the RC signal loss failsafe feature is working 100%. If the matching Futaba receiver is too expensive you might want to try the FrSky FAAST s.bus receivers which have must better pricing. I use the TFR8SB...

PID loop control has been common to industry for many years. Foxboro developed a self-tuning PID controller many years ago. It was advertised to have AI - artificial intelligence not long after the term first began to appear. The fundamental principle is that a PID loop controller is optimized...