Search results

usually the 12amp and under are used for the smaller quads and the 20amp + are for the bigger size. I'd recommend getting the ones I posted a link to on my other thread but any will do and you should get at least 1 extra one in case you blow one up.

well I guess anything will work as long as it gets hot enough. putting on 2mm or 3mm bullet connectors is the easiest way I think.

it's extremely important that no metal part is exposed. I've made 3 fires and make it stink so bad and broke a motor cause I had some metal making contact.

whaaaaa, I think a gun is too big to be able to do it easily without touching other nearby parts that could damage it. If you use a soldering iron with a medium to small tip it will be easier. As long as you wait long enough for it to get real hot you just barely touch the solder and it'll...

i just built a 450 size quad with apm 2.8 gps and i just put a cheap eachine ccd 600mw camera on it with an upgraded antenna.

has water gotten in it? maybe a circuit got fried a little.

did you set your transmitter to be in ppm mode? I'd use cleanflight. baseflight acts wonky from my experience.

ummmmmmm what? make your control command 1000

For me it's the ESCs. I've burned out like 4 ESCs, ended up swapping out ESCs for the same build twice. It's been my fault but for a newbie I think you really need to buy the ESCs that will make it easy for you to solder the motors to if you don't wanna use those bullet connectors. I finally...

I just ordered the skyline32 mini. It's got a compass too so I can fly in headless mode which I LOVE. I have an advanced model in my 260 frame now and it flys perfectly every time. It's just like a quad you would by that's prebuilt in a store.

If I were you I'd get one of the skyline models. either acro, advanced or mini.

NO PROGRAMMING KNOWLEGE IT'S REAL EASY WITH A EASY TO USE GUI. I HAVE A RADIOLINK AT9 TRANSMITTER AND USE A R6D RECEIVER IN PPM MODE. JUST MAKE SURE YOU ENABLE PPM IN THE SETUP PAGE IF YOU USE IT.

Blheli escs, kingkong 260 frame, eachine 600mw camera, 2200 lipo, discovery buzzer, skyline32 advanced, 5v ubec, blue leds on tail n green in front with 4 modes controlled by remote, top red siren light controlled by remote, 6in propellers, 2204 motors, a lot of electrical tape to cover up the...

I have two cc3d flyers and I really like them till I got a naze32 skyline advance the has the barometer and compass and everything and it was so easy to setup and I love to fly it in headless mode I have found that it didn't require as much trim and I didn't have it many problems with it flying...

So i pretty much put it all together with some neat lights and can fly in head free mode really nice but its way to sensitive for me. Im use to the cc3d where i set the max tilt to 20 degrees and itll go nice n steady n slow even if i pushed the stick all the way. How can i do the same on the...

no firemen love to do other things to get out of the building! go ask

I would doubt removing such little weight would do anything. How about get a 5500 battery for your main battery .

I think you can get a really long stick somewhere. I know you can find long things in hardware stores but having to buy something will prolly cost as much as the thing. Unless you buy some long sticks and connect them together then return it that would work. I have a 10 foot long wooden stick...

fly a larger drone with a fpv camera pointed down and a hook on a string and then you can try to lift it up. or go to the near by fire station and ask them.

I took the apm off my top and did the calibrations where you put it on its sides and top and bottom on a box on a flat surface so that should be spot on now. So I'll put it back on later and then do the live calibration where you gotta turn it all around cause I know I didn't do that right but...