Recent content by eyeinthesky

  1. E

    Pixhawk + S800

    Hi People i have a new 3DR pixhawk and i want to install it into my DJI S800 frame. The first thing i need is a Power module that can handle a 6 cell because the stock one doesn't. I found this one.http://www.ebay.com/itm/301131264504?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT...
  2. E

    Need Help with my S800. Two questions

    I recently started Flying my DJI S800 it sat on the shelf for a while i have flown it in stock condition with the IMU mounted in the stock location on the center flown lots or times no issues. So my question is #1 Should i buy the high frequency vibration isolator kit and mount the imu on the...
  3. E

    Aeroxcraft New! - Landing Gear for DJI F550 for use with Aeroxcraft GoPro Gimbal.

    Hi can you make this with a gimble for a point and shoot camera ?
  4. E

    I want to test my failsafe without turning off the TX

    I did a search but i still have questions Futaba 8FG i want to test the fail safe function, i already went to the calibration screen and programed my TX to trigger Fail-safe when i turn off the TX (and it works ) but im afraid to turn off the TX mid flight. I want to trigger the Fail-safe by...
  5. E

    DJI F550 which replacement props?

    can you post a link when you have them in stock
  6. E

    Dji multirotor videos here.

    Gopro hard mounted underneath, stock motors and ESC , stock 10 in props, 3S lipo, Wookong HEXA .
  7. E

    Aeroxcraft Quad-670 (for DJI) - Now on Sale

    nice frame
  8. E

    motor sometimes spins backward on startup ??

    i have the stock motors and the stock optio 30 A ESC its exactly as you guys described only happens sometimes and it corrects itself after a restart.
  9. E

    motor sometimes spins backward on startup ??

    sometimes one of my motors spins backwards ( or not spins at all ) when i initiate the combination stick commands (CSC) once it corrects itself it flies fine. Sometimes i just restart the motors or sometimes i just spin it by hand to get it going the whole setup is brand new about 10 to 15- 5...
  10. E

    don't use DJI props they snap 8"

    its always a good idea to constantly check for wear and tear even with expensive props
  11. E

    Line loss help (voltage calibration )

    So you only put the voltage of one cell or did you mean 1st lvl 11.4 loss 0.2 2nd lvl 10.8 loss 0.2
  12. E

    Line loss help (voltage calibration )

    Can someone with the stock motors and a three cell with 30 A ESC give me an example of what they imput into the voltage monitor screen I need a little help to get more flight time out of my batteries. right now when the yellow flashes and i land theres is still allot of juice left in the...
  13. E

    Line loss help (voltage calibration )

    so i added a .3 to the line loss and i calibrated the battery with a multimeter but now the yellow(first level) starts flashing and i still have 3.9 volts per cel lso basically its coming on too soon . how do i get it to come on at about 3.6V per cell ??
  14. E

    Line loss help (voltage calibration )

    trying to calibrate the first and second level battery protection. but don't really understand the line loss part as it is when the yellow led kicks in the battery is still at 3.8 V per cell i think i can get more flight time out of it : any tips would help
  15. E

    Hi from NorCAL

    whats up guys and gals just put together my second multirotor im using the DJI-WKM with the Hexa frame probably post some videos down the road.
See more
Top