Recent content by europe

Hi, I believe wifi is only applicable for Nex-5r and Nex-6 but I might be wrong? Still haven't done any testing with this link to verify whether the 2.4 GHz RC is having trouble. I will for sure test this thoroughly in order to avoid surprises during flight.:livid: I am using a standard DX-8...

Ok, that explains why. Thanks for your info. I registered and requested (wished for) a new app that could control both mode settings and the power zoom. Excited to see if/when such an app is released.

Come on guys, really, no one that has found a suitable piece of software?

Hi, anybody that knows of an iOS app where you can change settings on your cam such as shutter/aperture/photo mode etc. from your iPhone using the wifi connection? Maybe even control the power zoom (16-50 pancake)? All I've found are too simple and only provide live view and remote "take...

Just to be sure - have you checked your voltage reading with a multimeter so that the Naza sees the same voltage? (Voltage calibration)

Ok, stupid question maybe, but what if I bind the radio to another receiver and just move one wire a time from the Naza esc connector side to the throttle channel of this new receiver? Does it make sense? I guess you guys already requested the option to run motors individually as a software...

Hi, I suspect a bad bearing on one of my quad motors. Is there an easy way of running the motors individually in order to test/listen/measure? Running Gaui stock 18A ESC´s with Tiger MT2216 motors on my 500XT. FC is Naza M GPS on FW 3.12 Thanks!

Hi Bruce and thanks for your input :) Most of the fact regarding my hard fail-safe landing is to be found here http://www.multirotorforums.com/showthread.php?12444-Tested-failsafe-with-a-not-so-good-result As you can see, it was a fail-safe verification test which didn´t turn out as I was...

Heureka! Got it! Thanks :) With this in mind I guess z- position is totally irrelevant for the craft to calculate necessary thrust in order to slow down descending velocity? I have my very hard fail-safe landing in mind...

Thanks for your input. Slowly beginning to get a grip. But the accelerometers are located in the main unit I guess? Still puzzled by the fact that you have to enter offsets in cm for a sensor that collects GPS data? And how can a faulty Z-value by a few centimeters affect the ability to land...

Hi, it says in my manual that I have to change the values (X,Y,Z) offset from center of gravity, each time a change the all upp weight (eg add/remove a camera). How will these numbers affect the behavior of the bird? To me it seems that it flies equally good even when I add a Nex-5 (about 450g)...

I've just replaced the Scorpion motors with these http://www.pitchup.se/index.php?route=product/product&path=89&product_id=2031 and use either a 3S 30C Zippy 5800mAh or a 3S 30C 5500mAh Gravity. Gives me about 7 min. duration which I believe is enough for still images.

My quad weighs 2150g and out of this about 450g is camera equipment. I used 11x4.5 Tiger CF props which gave me plenty of lifting power. I will double check the balance point which I guess is the same as COG? I also got the impression that the descending from 20 metres was simply too fast to...

Ok, by GPS calibration you mean the Naza dance? I didn't get any indication of GPS or compass problems. The quad was rock stabile both in position and direction and I left it hovering for about 30 sec. to wait for a passing car just before I engaged fail-safe. It performed a perfect position...

Hi everybody, today I decided to test failsafe for the first time. I flew away about 100 metres and "parked it in the air", then flipped the fail-safe switch at about 5 metres altitude. It started by descending a meter or so, then went up to 20 metres, turned towards the take off point and came...