Search results

You better consider removing the WK-m on your expensive setup, i had it removed from my Cinestar8 because after tuning with every possible parameters, i still cannot get rid of the yawing (coupled with wobbling) issue. What if it goes into a wobble of death from high altitude !!!

I am having this YAW tuning issues for a long time, I can't do a flat yaw(rudder) turn without wobbling... I have test with different parameters for the settings, till i finally gave up. This set was on my Cinestar8...and it became a joke for video taking. Now i have downgrade this WKM unit...

**** ! I crashed my other set powered by Mwc... It was due to a very bad soldering joint in the motor lead that connects to the male bullet connector. I was able to pull it out easily from the male bullet, and it didn't break the wire, cos there is a hole where the wire was ! Learnt my...

I split the shrink rap on the esc, removed the esc's female motor leads, then soldered the motor wires directly onto the esc tab, then i used back the shrink rap and tape with scotch tape...

Finally tested out my f450 without bullet connectors, i have flew 5 packs of lipos, so far no issues of dropping off in the air, all flight was locked on, as commanded from my Tx radio.... I did twice failsafe home return, beautiful too. Hopefully removing those bullet connectors solves my...

Ok, I have spent the last hour dismentleing the escs and removing all bullet connectors. Now the motor wires are permently soldered to the escs, rechecked all solder joints and are happy. Will test fly tomorrow and report my findings...

I am also having some problem alike. I have a f450 with Naza for quite a while, good flight so far, but recently it just drop out of the air and landed upside down, FC disarmed the motors, due to upside down...but when i saw nothing damage, i flipped it over, armed it and flew again with no...

Its not gonna work, because Naza gps unit has a magnetometer chip built inside, where else the one on the link is purely GPS unit. They even make sure WK-M and Naza gps unit cannot be interchange.

For me, i support both sides, i bought a original Ecilop and going to buy alot more steadicam or clone set.... For the plain reason, this hobby craft will fall out of the sky one fine day, so i need back up. Buying the original makes sense, coz the original designer need to make some money, it...

i am using simonk reflashed 30A esc

I just received it thru my mail, i should say, not a single instruction sheet given inside the box. When i went to the website to try to download the manual, it was mostly in chinese, i can locate the installation manual and softwares. Pretty disappointed at the moment. Anyone know where to get...

Checked that ! The GPS module was epoxied to the shaft on both ends. Also check that the direction of the motor and prop's direction, all as per DJI's manual. Can any kind soul out there, pls do a full yaw stick command on your TX and see how your craft behavior.

Congrat to your new addition to your hanger. Since its built by a professional, it must be well tuned. DJI's product performed flawlessly especially with position hold and alt hold. Can you please do me a favour? Do a full command YAW stick left or right, and see how your craft behavor. See...

I am using the latest firmware.

I have been flying DJI WKM and Naza for a year, all seems ok...excellent on the gps thingy. But both my set got serious YAW problem, my naza( quad) and Octo (WK-M) have stability issues when i do a Yaw command on my rudder stick, both will jump up and wobble, causing the need for me to regain...

Haha, this is a good one, i am selling my WKM too, any takers ?

I am putting it into a 850 sized Hexa, it will carry my GH2.

Awaiting for my set to arrive.... How come this thread is so quite ? Is it so good that users of Zerouav set doesn't have any issues ? I hope so...smooth sailing.

Have you physically seen and hold a DJI Zenmuse ? LOL

I just told you i had one with me, considering to sell off and buy DJI's. Its simply constructed by using afew carbon rods and many plastic U clamps...I didn't say it won't work well, just that the it look like its make by some back yard inventors.