Search results

Hi all just a quickie to see if anyone else has had the same problem with skyjib 6 landing gear mounts?? i had these made from alutec high end aircraft ally.... 52g each.. These are not just a bit of cut angle, these have been wire eroded from one 50 x 50 x 150 block of ally.. (no week point) If...

Hi all Anyone out there able to translate english to hungarian.... yes, there is a girl involved. LOL. Regards David

hi mike, i dont have a spare channel available for RTH, but it is set up for TX in off mode... works well.... Do I need to set my home position?? do i have to put it on the floor and adjust the altitude levels?? i have no idea what i am doing. regards david

Hi Mike i have been reading all your advice on the previous posts and you seem to have the best handle on the whole thing.... which is good for me and bad for you, because i need help!! lol. I am really really usless at these things and i can even understand what i should be doing and testing...

Hi Mike Thanks for your reply... Im thinking of doing test over a cornfield as its the softest crash i can think of... lol. The camera is all insured but the skyjib6 is not!! i think will just have to grow a pair and do it.. Still not sure if i have to take off and hover or does the DJI veiw...

not done my test yet..... Oh mate..... thats just horrible..... I have just set up my DJI view but i have not done a test yet. To be honest, i have no idea how to test it or even how to program it.... any advice on first test and programing? im crapping myself as not only is the hexcopter some...

hi all fitted it at last, helped loads with high winds..... really happy :tennis:

hi whilst i would love to take all the credit, it was built for me by Andrew of 'www.multirotorcraft.co.uk'...... you can get the cable sleeve from http://www.cablecraft.co.uk/ProductGrp/braided_sleeving regards david

cheers hjls3, i will keep you posted.......

hi zaxis i have just balance the props, so i will give it another try first...... but then, yes, i will lock out the whole lot and see what that does... i have tried two cameras, canon 7dslr and canon g7 full auto..... same, but different effects. regards david

hi hjls3 i have just balanced my props and have yet to test it... i fould 2 x blades and 2 x hubs slightly out..... sandes down the blades and added super glue to the hubs..... fingers crossed. regards david

hi thanks again for advice. i have only the standard vibration damber that comes with the 360 av200 (4 x black rubber grommets) is ther something else i can use?? the house seemed very interesting.... until i brought it and now its a pain in the backside.. I am bbuilding a bit on the back now...

Hi dktek, I do have the doubler plate installed. . I have posted 3x photos off MR on another thread I started on, the jitters in this forum. . Regards david.

hi all, thank you for all your input... i am working my way through the list of causes... just confirm, my 360 is disconected and cable tied rigid. i have attached 3 x photos of the build up, i have not got the dslr on there at moment becaused i plan to take off the tilt belt to balance the...

my MR set up is: Skyjib 6, Axi 4120 motors, 15 x 4 beech props, Dji wookong fc, 80a esc, Av 200, 360 pan (fixed solid at moment, waiting for PH stabiliser) The props are new and have not been balanced by me since purchase, How do I balance props? Also, how can I make sure the motors are...

i dont think the av200 has a problem, its just the vibrations that are through it when i have a camera on board.. what is the best way to check where the vibrations are from?? what should i check for first if not the av200? did you look at the video?? if so, what do you think the issues are...

hi all, i have major video problems with my av200... when i use a dslr, it seems to be 'stepped vibration' when i use the canon g7 auto, it has vibration..... i have attached a video below, could you let me know your thoughts and solutions..... i am willing to try anything. i have tightened...

http://www.youtube.com/watch?v=onpx5R7Kk6A&feature=g-upl

av200 jitters hi all, i am getting some vibration through the av200 gimble and see that you have given this alot of thought and have overcome your issues with yours... can you help me with mine?? i have mounted a canon 60d (seems to have a very 'stepped' video recording) also a canon g7 auto...