Search results

Thanks for all the responses it now works fine. I am looking at getting a FPV set up and would like some advice. I am looking at getting; Sony 700TVL 1/3inch CCD FPV camera Boscom 5.8ghz 500mw 8ch wireless av transmitter - T5352 Boscom RC305 receiver Just wounding if any one had experience...

Swapping the wires worked perfect. Thanks for your help! :D I did notice it was pulling heavily to one direction, but I can play with that tomorrow and re calibrate the compass to hopefully sort that out. :D Thanks again. :D

Success it all is working after reseting and re doing everything :D I have now balanced the props and put them all on. It isn't taking off thou. I think one of the motors is turning the wrong way. Any ideas on how to change the direction? I have the 2 props marked wth a r on oposite each...

Trims are all centred on the tx. Thanks. Still no effect

Andy all settings match as you said. Still no effect . Thanks

Jbrumburg YesAll movements go to 75% on the display on the tx when in full lock. Thanks

Checked the settings on the tx and all are default. The only settings that have been changed is the program mix. Mix 1 State act Master Gea Slave pit Offset 000 UPRATE 035 DNRATE 000 SW nor Mix2 State act Master Gea Slave pit Offset 000 UPRATE 040 DNRATE 000 SW id1 The only other option that...

Battery has been fully charger and ballance. Still no joy! What do you mean check the end points? I have done the stick calibration on the Naza assistant and it's seems to work on the software. I.e if I move the control to the left it shows on screen etc One thing I have noticed is that if I...

Andy, All the red wires from the ESC's have been disconnected. Thanks

New batteries gone in to the Turnigy 9x reading 11.7v on the screen Lipo has 11.30v according to the Naza assistant I have put it in calibrate mode and calibrated as your meant to and yes made sure they are in the center position before doing the calibration. I am arming as you are meant to...

Yes to all the above. Thanks

If it is in gps mode it flashes green and red or if in atti mode it flashes orange and red. Thanks

Plugged into assistant and re calibrated the sticks with the same result. Thanks

UPDATE - I have managed to calibrate the compass after walking around to find the perfect spot in my garden! 5 attempts later and it works! Unfortunately I still can not get this thing to start the motors and fly! :( SO CLOSE!!!

I have tried to calibrate exactly how it says to do it, same way as you said and it still does not work on the vertical. Maybe I should try to calibrate it in a different location as my garden does not seem to work. In atti mode I am unable to get lift off. I followed the Combination Stick...

Andy, I have adjusted the hold settings, I now get 1 green and three red in GPS mode which suggest poor signal, I tried a different location and this has now changed to 1 green and 1 red :D and I know have 1 orange and 1 red in Atti mode . Happy days! I have tried to calibrate the compass as...

Andy, i have followed the video you sent me, thanks. I now have a working U channel and can switch between manual,gps and atti. The next issue is the thing wont fly!!!!! I have set it all up all controllers and everything work just fine. When i turn it on i get the system start and self check...

how would I do this in acro mode instead? Thanks

Andy thanks again for your replies / links. I did see this video myself but this uses the Turnigy 9x in heli mode? Most comments and links / setups I have seen have said to use acro mode? Does this effect anything? Thanks

Just so you know, I have set up the Turnigy controller with the following settings as per a video on youtube. All works apart from lining up the U channel 3 position switch with the manual, gps and atti fields. Go to the AUX-CH menu and set CH6 to "PIT TRIM' The Pitch Trim dial will be the...