Search results

Sorry, RTRyder, I didn't really get you: Is the WKM good for changing weather conditions and wind or not?

That helped a lot! Thank you very much!

regarding the left over error: does anybody know what the reason for this is? I don't understand it...

My Roll gets out of horizon when I pan or rotate the aircraft. About 8 degrees, then slowly it goes back into good horizon. This is the "left over error", right? Changing the roll integral gain doesn't help at all, I cannot see a difference if I put it to 100 or 500. My gains: tilt position 170...

I have problems with my pan servo. I am not able to start and stop panning smoothly. Which pan servos do you use? I got the hyperion ds16-fcd on my av130.

Thanks for the pictures, it would be interesting to know which HARDWARE version do you use.

Pixvertex: you have no jitter problems with your setup? Could you be so nice and send us a photo of your setup? That'll be great!

I solved my jitter problem! On the 2nd hole from bottom it's working better for me, even if I have to go out of roll balance to be able to tilt 90 degrees down. The roll can handle the out-of-balance much better than the tilt. Anyway, that works o.k. now, but I figured out a new problem: if I...

Which camera do you use, PondMedic? Maybe it's relevant how good you could level your camera in the AV130. My problem is that I have to put the tray in the lowest position to be able to operate the CX730 and then when I tilt it the camera is front heavy, the tilt servo has to fight against it...

did anybody try capasitors to solve the jittering?

still jittering The camera tray is already in the lowest position. With the Sony CX 730 I have to be there otherwise I couldn't look 90 degrees down. A little video of where I am now (the flying video is stabilized by CX 730), still jittering…: http://youtu.be/Pi93EIrZwvQ Any ideas what I...

I am very very happy with the results now (1.2.2 / av 130 / felt washer on tilt). But there is still a little jittering when the camera is tilted down. I balanced the camera position as good as I could and in horizontal position there is no jittering at all. But when I tilt down, the camera gets...

that's right, jffry! I did a quick connection diagram:

Thank you very much for the hint how I can set it manually. Sometimes you can't see the wood for the trees. With roll it works very good now with manual tuning. With tilt I do auto tuning and I'm fine now and only have to do fine tuning and can't wait to do a test flight! Thanks a lot! Andy

Soaringclauz: I would really like to do manual tuning! With my software 2.1 it's not possible because there is no button like this. In older versions there is a button but it's not working neither... No reaction of the servos when I change the values. Does anyone manual tuning with firmware...

Auto-Tune doesn't work on FW 1.2.1 & AV130 Auto-Tune: the roll always hits the dead end stop very roughly and stays there while the servo tries to go on. But: if I disconnect the tilt the Auto-Tune does work for the roll. But for me the stabilization worked better on firmware 1.6. (I always...

then it's jittering too much. I would like to understand the problem... what is the difference between holding it in the hands and flying in terms of stabilization?

How does it come, that the stabilization is fast&perfect when I hold the Hexacopter in my hands but when I fly it's a bit too slow? Of course I have separate batteries for the hexacopter and the remotehead/skyline. I had the same problem with MK stabilization (with separate batteries, too). Any...

I'm on 1.1.7 now, it works fine, even with auto-tune, but is full of jitter until I unplug one of the servos. If I use skyline only for tilt or only for roll it works very good. Does anyone have a good power scheme for me how to power the reveiver/skyline & the servos separately? That should...

if anyone could share 1.1.7 with me: thanks!!!