Search results

Swap two motors from opposite sides of your multi as suggested previously. If the problem moves with the motor position change, you then know the issue is with the motor or bullet connector ends. If the issue doesn't move with the motor swap, then the issue is with the ESC or the controller...

I also live in Alberta, i.e., Calgary,Been flying Naza @ -5 to -9 deg C with no issues re: attitude or GPS. Where are you located and when/where did you get your WKM....? I tried to get one but gave up after 1/5 months due to US supplier delays in combo with factory recall....so I bought the...

Naza specs indicate -10 deg C is OK while the WKM specs call for -5 deg C minimum. Internal pcb temperatures should be a couple of degrees higher than ambient when powered but wind chill effect can suck the heat away from everything when moving quickly. Keep in mind that temperature typically...

All issues resolved now...... It's much simpler than I realized. Just plug the gimbal servos into Naza ports F1 and F2! From section 5 of the manual, subsection 3. After adjusting the servo directions and centerpoints per section 5 (2) Gimbal set the F1 and F2 gains at 10 each and X1 Manual...

I am trying to use eCalc for my F550 c/w Naza etc. While there are many motors to choose from, I do not see and entry for the DJI 550MOT motors. Is there an equivalent motor that I can select or a custom setting I can use for 920 rpm/volt?:cold...

The voltage at the output terminals of a dc power supply or battery typically drops when the load is removed. RE: LEDs to use... check out the following to answer most of your questions. http://www.rc-cam.com/led_info.htm

I am about to test two servos for camera gimbal control on my F550 c/w Naza M-GPS including the V-sen to manage the electrical power distribution. I am looking for some direction as to the configuration of the hardware and the RC transmitter. I am using a R6208SB in FASST MLT2 configuration and...

Thanks Kloner..... I am a bit confused about the necessity for the 10 amp BEC so I am going to repost with additional detailed information re: my RC and Naza which came c/w with the VU, i.e., V-sen voltage regulator/distributor. If of interest, please see my reposting which will be completed...

Below is some first flight videos of my F550 c/w Naza GPS. Landing pad is a 4 x 4 foot corrugated plastic panel (landing pad) to protect the Hexacopter from snow! My stick handling is still a bit jerky.... But now I want to configure/add two servos for a camera. Once I get those working I will...

I think their recall was timely and the right thing to do..... a very professional company but something might be lacking in the dealer/reseller distribution systems which is US based for North America...i.e., US and Canada... IMHO..... just give it some time and be thankful you do not live up...

If these were computer products/components or car parts you would have your replacement parts already.... But this is a specialty area.....and China is a long ways away as is Germany for Mikrokopter parts. If you can deal with it.... be patient.... In my case I missed out on 6 weeks of...

If you start out with a Flamewheel F550 c/w Naza GPS you will have a good starting platform that can later be expanded to take many additional features and can even upgrade the Naza GPS to the WooKong M GPS before you move up to an Octocopter such as the S800......... at which point the sky is...

It's a great idea but not without significant challenges. Have you considered the sluggish response time of a gas engine compared to an electric motor? Gas engines are notorious for changing speed slowly as compared to electric motors. Now if you could design a gas driven micro electric...

I suspect there would be a bit of a worldwide backlog and the manufacturer is a long distance away. Where do you live?

RovGuy and Kloner.........Well..... there you go...... I knew some current had to move between the two...... but wasn't sure power through the back door, i.e., thru s or d.bus was what DJI-Innovations had in mind!!!! I tread cautiously!!!!

Locally there is a strong preference for Spectrum products (an exceptional and user friendly radio system)..... but they don't offer D.bus or S.bus capability which DJI-Innovations takes full advantage of. DJI-Innovations is very forward thinking in this respect as the world will eventually...

Kloner...... is it safe to assume that receiver is being powered by the s.bus and not the conventional Receiver power input receptacle? All I see is a 3 wire orange/brown/red D/S.bus serial link between the Naza and the Receiver........ Don't see a black and red wire anywhere......

DesJardins.... But what about the power cable to the R6208SB Receiver? Should it come from the VU? Can I buy a power splitter cable to split the power between the GPS and the Receiver? A direct connection between the 4S battery and the Receiver will burn up the receiver....!!!!

I recommend the FlameWheel F550 hexa c/w the DJI-Innovations Naza-GPS...... you can even buy motor arm extenders and increase the prop sizes a bit for heavier payloads..... within reason! I am now assembling a DJI-Naza c/w GPS on my FLameWheel F550 (hexa-frame). If you are moving forward in...

Futaba Receiver gets power from where? Naza vu or what... ? Must not exceed 7.4 volts dc... Using 4S multirotor battery! How do you all do this?