Search results

and if I may ask where did you get FW 1.5???????????????????

which camera was on the copter?

On question 1 ... check your end point or subtrim set in your radio. If the software is set up at 90 degrees that is the most obvious thing to look at. The other thing to look at for tilt is "Did you center your servo" , meaning remove the belt, go into software and move you position numbers (...

it's easy.... all else fails just reverse (change) it in your radio...

You can hook it up on a slider for tilt, take it out of slew mode and it will hold position BUT!!!!!!!! be very careful when you power up. You need to make sure your radio is on, power your Copter/or really the receiver ( that you are operating tilt with)on the copter BEFORE you power up the...

Oh I would soooo love to be able to use slew mode, but we cannot use it without a second camera operator. If you put Tilt on a slider or a pot it will constantly move from one position to the end of the other. for example, the operator cannot have tilt on a slider and and tilt to 45 degrees...

Y6 with hover fly https://www.youtube.com/watch?v=0nNfaZHrCpY Not my info this is from RCgoups.com, interesting reading for you jesolins Tri-Quad-Hexa-Octo-copters...

I had the same thought pattern after my original quad blew a prop and went down, wow they come down fast.. I went with a HLE8 after watching videos of a flat 8 losing a motor ( another with 2 motors gone) and still landing with everything intact. Yes you need some room to transport as they do...

From looking at the pics I would take it apart and address the cage. I bought an AV130 on this board from Thomb ,supposed to be a month old :( , and it had the same issue. The cage itself was bent out of shape. .. It took quite a bit of time to straighten it out but it can be done. take...

my oh my, the jitter is there for sure but your roll is awful.. Maybe it will work as advertised on the next version, right now I have never been able to make mine acceptable like the product "DEMO" video. Sending emails for tech support is a waste of time as one will get maybe one response to...

skyline twitch I am looking for a suggestion on my roll twitch. do I need to go higher for the correction or am I over correcting???? I tried the gains for 100 to 150 to 300 and did not see any difference. this is the last one at 300 Integral at 10 velocity at 150 Any ideas are appreciated...

Yes as stated earlier i do reset everytime and re enter all my values, I did it again yesterday 5.12a to 5.14 just to test and I get allot of white flashes just hovering in the back yard. revert back to 5.12a and the white flashes go away.. Got me man :topsy_turvy:

There is no secret to the upgrade. As I stated I do the default everytime then completely set it back up again. I love this board as there seems to be many professionals here , but if you want to read reports go to rcgroups.com You will re-think your "There has been hardly any reported...

Thanks for the thought but I think what you are saying is hook it up to assist software before every flight? That seems un practical... when I set up a craft I hit default values and then go thru a complete setup everytime I upgrade. If you read the rcgroup boards this is becoming a very...

MY Ship.. droidwrox octO HLE8, 2814, 30 dji esc, av130/360, 1245 carbon props I UPGRADED TO 5.14 YESTERDAY, FIRST FLIGHT I SAW, FOR THE FIRST TIME, WHITE FLASHES ONCE IN A WHILE. THE SHIP SEEMED TO WANT TO GO LEFT AND I ALSO HAD FISHBOWL FOR THE FIRST TIME WITH THIS CRAFT.(yes I did the...

sorry, allot from me today.. OK.. I did hand level, auto tune ( which always defaults to slew mode on tilt) it is level on both axis level and operates pretty good. I take slew mode to off as I it will only go to level or 90 degrees, nothing in between. If I try in between is moves to the ends...

tried that and no change at all in slew mode. It keeps moving not matter what, I even tried a three position switch even in the middle it want to keep moving one direction or another. any other ideas?

What is the best recommendation for roll setting? slew or normal, what is the difference between the two

should the red wire be removed for the input so there is not a double power source. I see no mention of this in the instructions.