Recent content by csr0831

  1. C

    VRX output

    I have a miminosd micro. Yes the monitor is fine except that display is shifted leaving a physical gap between the face of the display and the basil on the left edge. It works fine, but the guys at RMRC are sending me a new one with a box and shipping label to send the defective one...
  2. C

    VRX output

    Found the problem......I had the leads coming of the RX/TX pins on the board reversed. As soon as I straightened that out all is well. Thanks for helping me out on this! : )
  3. C

    VRX output

    well crap.......there goes that theory. Thanks for checking that out for me.
  4. C

    VRX output

    Your VRX (vedio receiver) was on and connected to the monitor, correct?
  5. C

    VRX output

    Coons made a mess.....not what I meant. I mean if I JUST turn the VRX on and hook it to the monitor even without an incoming signal to the VRX, shouldn't the monitor see ...."something"? some kind of carrier....obviously no picture, but snow, static, something? OR does it take an incoming...
  6. C

    VRX output

    Your sketch just came through....basically the difference between yours and mine is that you DO have a dedicated ground and going through the PDB I am not sure the ground for the FPV is isolated from the grounds for the rest of the system. But even if it's not, I would think there would be a...
  7. C

    VRX output

    I have bypassed the OSD (first thing I tried) to eliminate that. The 5v (and the 12) come from onboard step down regulators. There may be something to the ground loop theory. All my grounds are tied in to the PDB....did that to eliminate some of the wiring and that may be a problem. The...
  8. C

    VRX output

    Here is the sketch of the hook up.....
  9. C

    VRX output

    I will try and draw something up tomorrow and you're exactly right, it acts like it's not getting any input at all. Even if the quad wasent sending a sig, the VRX should be outputting something to the monitor even if it's nothing but a carrier, which should result in "snow" or "static" on the...
  10. C

    VRX output

    NTSC (I think) and no lens cap. I've been very satisfied with RMRC. : )
  11. C

    VRX output

    The monitor is an 8" rmrc FPV, VTX is a FX795T (5.8 gHz 40 channel), the VRX is a FR632 (diversity) and the FPV cam is a RunCam 600TVL Mini. I think the monitor is bad. Looking closely it appears as thought the entire display has shifted to the right opening up about 1/32 of an inch gap along...
  12. C

    VRX output

    Trying to get my FPV system working and I got nothing. The monitor I have sais it will not display a blue screen, yet that is all I see.....starts up showing AV/2 in the upper left hand corner and after a few seconds goes to No Signal in the middle of the screen, BLUE screen. It may be because...
  13. C

    OSD plugged in - no stick input

    Greetings all..... Any one have any idea why cleanflight would f ail to see the stick input from my transmitter if the OSD is plugged into the RX and TX pins in the middle of the board (Naze32 full rev6)? If I unplug the OSD, stick input returns. Ideas/comments/clarification/ridicule?? Any...
  14. C

    OSD (grrrr)

    I have downloaded and installed all the appropriate drivers. I THINK I have a bad board (FTDI board) There is no output on the 5v pin when it's hooked to a com port even though the LED is lit showing that it has power coming in..... I'll keep hammering at it....thanks John.
  15. C

    OSD (grrrr)

    Hi Folks.... I am trying to load the latest version of MW OSD on to my minimisd micro....with zero success. I have it plugged into my FTDI and I am not sure it's seeing the osd board. There is no activity on the osd (lights of any kind), but when I plug it I, two additional lights come on on...
See more
Top