I hate to do it, but I need to clear out some toy space.
SPECIAL OFFER FOR MultiRotorForums.com MEMBERS:
$3000 shipped INCLUDING A FREE GOPROHD including memory card!!
Testing the waters and putting my MK Hexacopter up for sale:
FULLY ASSEMBLED, FLIGHT TESTED, & READY TO GO!!! This vehicle is like-new and has only about 4 hours total flight time.
Flight Setup
Flight Controller 2.0 ME
Navi Ctrl 1.1
BL-Ctrl V1.2 Speed controller
MPX4115A Pressure Sensor
MK-USB
MK3MAG w/ ACC
MK-GPS
MK-OSD
Hexa power distribution board
All RECOMs installed, but servo pins need to be added to the MK board to fully enable the gyroscopic camera mount.
2x MaxAmps 5250 4S 14.8V INCLUDED
6x Pulso 2217/20 motors
T-REX 600 Landing gear
DELights programmable LED lighting
Rusty’s PPM Converter for Futaba Receivers
Futaba R617FS receiver
Mikrokopter hexacopter frame
Park 6V BEC to power onboard accessories
FPV & Telemetry Setup
Iftron 5.8Ghz Mondo Stinger Video TX & Nano RX
Sony FPV camera
XBee Pro 900 RPSMA Telemetry link (can be used either/or with OSD but not at same time as OSD)
Notes
Full assembled with leveled and damped mainboards. Internally run wiring is designed to minimize EMI/interference on mainboard components. Includes fully balanced propellers for each motor. Flies smooth, hovers solid, fully featured and ready to go heavy-lifter than can carry a full FPV and telemetry setup plus a GoPro, or a single pro-camera setup. A GoPro mount is installed but other video camera setups may require a change in landing gear, not included.
All firmware is up to date.
Extra GPS batteries will be included (replacement requires basic soldering and should not be necessary if you connect the MK to a Lipo and turn it on for 10 mins at least once every few weeks).
All you need is a Futaba 7C transmitter (other brands/models will work but you may need to adapt the PPM interface and replace the receiver if another brand of transmitter is used).
I will provide very limited support to help you get off the ground but the primary education will be yours and can be acquired through the quad rotor sections of the RCGroups forums, Multirotorforums, as well as the Mikrokopter Wikis. Mikrokopters are very easy to fly but they also offer a TON of features, some of which are quite complex but easy to learn with time.
Flight video example (I don’t get to fly often…this was one of the last flights I made other than testing functionality and charging the GPS battery). http://www.youtube.com/watch?v=_MxUXkrpiBg&feature=g-upl
Shipping is free to the 48 contiguous US States. For shipping costs outside of this area please contact me.
Shipping insurance will be taken for the total amount of the auction close.
No returns will be accepted for any reason.
If you use Paypal then PLEASE READ: BUYERS ARE RESPONSIBLE FOR PAYING PAYPAL FEES incurred during the transaction. When Paypal gives you the checkbox option of passing the fee to the seller or taking it on yourself you MUST opt to take on the fees. NO PAYMENTS WILL BE ACCEPTED UNLESS THE BUYER ACCEPTS ALL PAYPAL fees.
s m o k e y t i r e z
at
g m a i l . c o m
Thanks!
SPECIAL OFFER FOR MultiRotorForums.com MEMBERS:
$3000 shipped INCLUDING A FREE GOPROHD including memory card!!
Testing the waters and putting my MK Hexacopter up for sale:
FULLY ASSEMBLED, FLIGHT TESTED, & READY TO GO!!! This vehicle is like-new and has only about 4 hours total flight time.
Flight Setup
Flight Controller 2.0 ME
Navi Ctrl 1.1
BL-Ctrl V1.2 Speed controller
MPX4115A Pressure Sensor
MK-USB
MK3MAG w/ ACC
MK-GPS
MK-OSD
Hexa power distribution board
All RECOMs installed, but servo pins need to be added to the MK board to fully enable the gyroscopic camera mount.
2x MaxAmps 5250 4S 14.8V INCLUDED
6x Pulso 2217/20 motors
T-REX 600 Landing gear
DELights programmable LED lighting
Rusty’s PPM Converter for Futaba Receivers
Futaba R617FS receiver
Mikrokopter hexacopter frame
Park 6V BEC to power onboard accessories
FPV & Telemetry Setup
Iftron 5.8Ghz Mondo Stinger Video TX & Nano RX
Sony FPV camera
XBee Pro 900 RPSMA Telemetry link (can be used either/or with OSD but not at same time as OSD)
Notes
Full assembled with leveled and damped mainboards. Internally run wiring is designed to minimize EMI/interference on mainboard components. Includes fully balanced propellers for each motor. Flies smooth, hovers solid, fully featured and ready to go heavy-lifter than can carry a full FPV and telemetry setup plus a GoPro, or a single pro-camera setup. A GoPro mount is installed but other video camera setups may require a change in landing gear, not included.
All firmware is up to date.
Extra GPS batteries will be included (replacement requires basic soldering and should not be necessary if you connect the MK to a Lipo and turn it on for 10 mins at least once every few weeks).
All you need is a Futaba 7C transmitter (other brands/models will work but you may need to adapt the PPM interface and replace the receiver if another brand of transmitter is used).
I will provide very limited support to help you get off the ground but the primary education will be yours and can be acquired through the quad rotor sections of the RCGroups forums, Multirotorforums, as well as the Mikrokopter Wikis. Mikrokopters are very easy to fly but they also offer a TON of features, some of which are quite complex but easy to learn with time.
Flight video example (I don’t get to fly often…this was one of the last flights I made other than testing functionality and charging the GPS battery). http://www.youtube.com/watch?v=_MxUXkrpiBg&feature=g-upl
Shipping is free to the 48 contiguous US States. For shipping costs outside of this area please contact me.
Shipping insurance will be taken for the total amount of the auction close.
No returns will be accepted for any reason.
If you use Paypal then PLEASE READ: BUYERS ARE RESPONSIBLE FOR PAYING PAYPAL FEES incurred during the transaction. When Paypal gives you the checkbox option of passing the fee to the seller or taking it on yourself you MUST opt to take on the fees. NO PAYMENTS WILL BE ACCEPTED UNLESS THE BUYER ACCEPTS ALL PAYPAL fees.
s m o k e y t i r e z
at
g m a i l . c o m
Thanks!
Last edited by a moderator:
